BlackT
|
|
« on: February 04, 2019, 01:59:59 AM »
|
|
|
Hello, I want to get PIN from TT cluster so i can instal it in car. The cluster is 2003, and car is 2001. I need PIN so I can login in with VCDS and pair it to immo of the car. But I am not able to read PIN with vag-comander Is there any advice from you? Is ther any other program that can read this cluster?
|
|
|
Logged
|
|
|
|
mushtafa
Full Member
Karma: +3/-4
Offline
Posts: 121
|
|
« Reply #1 on: February 04, 2019, 02:21:49 AM »
|
|
|
I have no experience with the TT, but if you click on the Instrument/Immobiliser button, read the EEPROM, it should display the mileage and PIN
|
|
|
Logged
|
|
|
|
BlackT
|
|
« Reply #2 on: February 04, 2019, 02:36:31 AM »
|
|
|
I know but it doesen't read correct Forget to mention, i use only K-line, but I think connecting to can-bus wouldn't make any difference.
|
|
|
Logged
|
|
|
|
macxxx
|
|
« Reply #3 on: February 05, 2019, 05:28:52 AM »
|
|
|
Its a jeager MM - commander cannot read it , try vagtacho maybe
|
|
|
Logged
|
|
|
|
BlackT
|
|
« Reply #4 on: February 05, 2019, 09:50:06 AM »
|
|
|
Is it possible to use Vag tacho software with commander cable, or KKL, or galleto 1260, or VCDS 11?
|
|
|
Logged
|
|
|
|
roverguy7
Newbie
Karma: +0/-0
Offline
Posts: 4
|
|
« Reply #5 on: February 05, 2019, 10:07:29 AM »
|
|
|
I was able to read an 04 mk1 tt Jeager MM cluster with Commanderand KKL cable. I had to use Shadow1 for it to pull and it pulled a full 10000 blocks, but listed immo and vin where it was supposed to in the dump.
|
|
« Last Edit: February 05, 2019, 11:43:52 AM by roverguy7 »
|
Logged
|
|
|
|
Black_A4
Full Member
Karma: +1/-1
Offline
Posts: 51
|
|
« Reply #6 on: February 06, 2019, 12:42:03 AM »
|
|
|
Is there a proper tool availible which can read and write those clusters?
|
|
|
Logged
|
|
|
|
aef
|
|
« Reply #7 on: February 06, 2019, 01:11:41 AM »
|
|
|
carprog from codecard.eu
|
|
|
Logged
|
|
|
|
Black_A4
Full Member
Karma: +1/-1
Offline
Posts: 51
|
|
« Reply #8 on: February 06, 2019, 03:47:06 AM »
|
|
|
An X-Prog Clone can not be used?
|
|
|
Logged
|
|
|
|
aef
|
|
« Reply #9 on: February 06, 2019, 03:53:40 AM »
|
|
|
letmegooglethatforyou lazy germans
|
|
|
Logged
|
|
|
|
BlackT
|
|
« Reply #10 on: February 06, 2019, 04:13:10 AM »
|
|
|
carprog from codecard.eu
Is there anything cheaper? I was able to read an 04 mk1 tt Jeager MM cluster with Commanderand KKL cable. I had to use Shadow1 for it to pull and it pulled a full 10000 blocks, but listed immo and vin where it was supposed to in the dump.
Tryed that no luck, direct MM reset cluster and after that commander shuts down
|
|
|
Logged
|
|
|
|
Nothery1952
Newbie
Karma: +0/-0
Offline
Posts: 2
|
|
« Reply #11 on: February 24, 2019, 03:03:45 AM »
|
|
|
Search for the pattern AUZ* @eeprom mapping location between 0x3800 and 0x3FFF. The two bytes before the search pattern is your pin. For example @0x3B90 FF FF FF FF FF 02 18 F4 41 55 5A 35 5A 30 42 39 -> ÿÿÿÿÿ. .ôAUZ5Z0B9 0x18F4 coverted to decimal should be 6388. Don´t forget the leading zero that means you have to enter 06388That´s all! Sorry I´m to lazy to upload a picture.
|
|
« Last Edit: February 24, 2019, 03:06:28 AM by Nothery1952 »
|
Logged
|
|
|
|
BlackT
|
|
« Reply #12 on: February 24, 2019, 03:24:30 AM »
|
|
|
Vag comander read eeprom only to 0x200 adress
|
|
|
Logged
|
|
|
|
roverguy7
Newbie
Karma: +0/-0
Offline
Posts: 4
|
|
« Reply #13 on: February 25, 2019, 10:03:03 AM »
|
|
|
I would try a few more times with commander. I was able to get one to read, but it did take a few attempts. Try with both Shadow1, and MM Direct. I ran into an error one time when I didn't run commander with administrator privileges.
|
|
|
Logged
|
|
|
|
b62.7t
Newbie
Karma: +0/-0
Offline
Posts: 2
|
|
« Reply #14 on: February 27, 2019, 12:54:24 AM »
|
|
|
I just did this, I got a MK1 TT with the MM, I used vag comander and tried all thre options for the MM. MM direct pulled the whole thing then tried what Nothery1952 posted and it worked.
|
|
|
Logged
|
|
|
|
|