Please Validate my custom bench table Harness

Pages: [1]

« previous next »

Author

Topic: Please Validate my custom bench table Harness (Read 7275 times)

professor

Sr. Member

Karma: +25/-0
Offline

Offline

Posts: 409

	Please Validate my custom bench table Harness « on: February 24, 2012, 05:08:43 AM »

Picture is attached please validate it.

Thank you.

P.S: ECU is for illustration purposes only, this harness will be used on ME7.1 & 7.5 ECUs.


« Last Edit: February 24, 2012, 05:19:33 AM by professor »	Logged

Seat Ibiza MK4 Cupra 1.8t 20V, stg3.
"Those 1.8T 20V machines are really tough" ©

professor

Sr. Member

Karma: +25/-0
Offline

Offline

Posts: 409

	Re: Please Validate my custom bench table Harness « Reply #1 on: February 25, 2012, 12:53:07 AM »


	Logged

Seat Ibiza MK4 Cupra 1.8t 20V, stg3.
"Those 1.8T 20V machines are really tough" ©

littco

Hero Member

Karma: +52/-7
Offline

Offline

Posts: 903

	Re: Please Validate my custom bench table Harness « Reply #2 on: February 25, 2012, 09:22:03 AM »

Looks good but you don't need 12v on pin 21 and no 6ohm resistor needed for the boot pin on 24.


	Logged

professor

Sr. Member

Karma: +25/-0
Offline

Offline

Posts: 409

	Re: Please Validate my custom bench table Harness « Reply #3 on: February 25, 2012, 11:08:19 AM »

Thank you for your answer.

According to image i attach 12V should power PINS: 3 ,21 & 62.
Also A resistor from my experience should be used, cause my ECU was broken after trying to ground it without resistor. A 6k Ohm would be ok?


	Logged

Seat Ibiza MK4 Cupra 1.8t 20V, stg3.
"Those 1.8T 20V machines are really tough" ©

professor

Sr. Member

Karma: +25/-0
Offline

Offline

Posts: 409

	Re: Please Validate my custom bench table Harness « Reply #4 on: February 25, 2012, 11:09:14 AM »

The above post attachment.


	Logged

Seat Ibiza MK4 Cupra 1.8t 20V, stg3.
"Those 1.8T 20V machines are really tough" ©

carlossus

Sr. Member

Karma: +38/-0
Offline

Offline

Posts: 394

Leon Curpa Stg1+

	Re: Please Validate my custom bench table Harness « Reply #5 on: February 26, 2012, 09:38:02 AM »

Quote from: professor on February 25, 2012, 11:08:19 AM

A 6k Ohm would be ok?

Better to stay < 1k or you might not pull-down effectively.


	Logged

professor

Sr. Member

Karma: +25/-0
Offline

Offline

Posts: 409

	Re: Please Validate my custom bench table Harness « Reply #6 on: March 01, 2012, 02:13:17 PM »

Changes:

Switch is connected to pin 3 in order to simulate ignition key.
Pin 62 is continuous powered with 12+V.

Pin 21 is not used.

I test 6k Ohm and 10K Ohm resistor and boot mode was enabled without problem.


	Logged

Pages: [1]

« previous next »

Jump to:

Navigation

Personal Tools

November 23, 2024, 07:36:49 AM

Welcome, Guest. Please login or register.
Did you miss your activation email?

Navigation

Personal Tools

Search