Maxohio
Full Member
Karma: +3/-3
 Offline
Posts: 83
|
 |
« Reply #45 on: April 19, 2019, 12:02:26 PM »
|
|
|
Hi, no original downpipe, 200cells racekat now
So, everything stock, only 200 cells cat |
|
|
|
|
Logged
|
|
|
|
|
sonique
|
|
« Reply #46 on: April 19, 2019, 12:29:03 PM »
|
|
|
ok
plz upload file
|
|
|
|
|
Logged
|
|
|
|
Maxohio
Full Member
Karma: +3/-3
Offline
Posts: 83
|
|
« Reply #47 on: April 19, 2019, 12:52:37 PM »
|
|
|
ok
plz upload file
Here you go, hope you find something. |
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #48 on: April 19, 2019, 01:17:03 PM »
|
|
|
you problem not imx or q2
never need very low KFLDRL or KFLDIMX auq engine
Disagree. If the wg is set very hard, it is needed. He could also try less WG pressure. |
|
|
|
|
Logged
|
|
|
|
fknbrkn
Hero Member
Karma: +177/-18
Offline
Posts: 1401
mk4 1.8T AUM
|
|
« Reply #49 on: April 19, 2019, 01:25:32 PM »
|
|
|
is it stock wg spring? if yes then you had a mechanical problem. check n75, lines and wg
also ldrxnzk def is wrong. you changed map axis size right after it @1F2AA
|
|
|
|
|
Logged
|
|
|
|
Maxohio
Full Member
Karma: +3/-3
Offline
Posts: 83
|
|
« Reply #50 on: April 19, 2019, 01:30:07 PM »
|
|
|
is it stock wg spring? if yes then you had a mechanical problem. check n75, lines and wg
also ldrxnzk def is wrong. you changed map axis size right after it @1F2AA
I think its stock. |
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #51 on: April 19, 2019, 01:39:04 PM »
|
|
|
I don't see anything mechanically wrong with the WG or the n75.
The PID just isn't tuned right for this set up.
|
|
|
|
|
Logged
|
|
|
|
Maxohio
Full Member
Karma: +3/-3
Offline
Posts: 83
|
|
« Reply #52 on: April 19, 2019, 01:52:03 PM »
|
|
|
Any details for what table data i should change?
|
|
|
|
|
Logged
|
|
|
|
fknbrkn
Hero Member
Karma: +177/-18
Offline
Posts: 1401
mk4 1.8T AUM
|
|
« Reply #53 on: April 19, 2019, 02:01:16 PM »
|
|
|
1st of all get back to stock 0x1F2AA
|
|
|
|
|
Logged
|
|
|
|
|
sonique
|
|
« Reply #54 on: April 19, 2019, 02:05:18 PM »
|
|
|
Here you go, hope you find something.
i sent for you file check your pm |
|
|
|
|
Logged
|
|
|
|
Maxohio
Full Member
Karma: +3/-3
Offline
Posts: 83
|
|
« Reply #55 on: April 20, 2019, 04:38:18 AM »
|
|
|
i sent for you file
check your pm
|
|
|
|
|
Logged
|
|
|
|
Maxohio
Full Member
Karma: +3/-3
Offline
Posts: 83
|
|
« Reply #56 on: April 20, 2019, 11:14:05 AM »
|
|
|
Ok, lowered LDRXN at the point it was reaching maximum wastegate dutycycle. How is this looking ^^? |
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #57 on: April 21, 2019, 10:05:55 PM »
|
|
|
Better but you are out of injector up top and you have too much DIMX still.
|
|
|
|
|
Logged
|
|
|
|
Maxohio
Full Member
Karma: +3/-3
Offline
Posts: 83
|
|
« Reply #58 on: April 22, 2019, 12:59:53 AM »
|
|
|
Better but you are out of injector up top and you have too much DIMX still.
Thanks Nyet, could you please explain why the DIMX needs to be lower? To take away the overshoot? And also the higher actual than desired? |
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #59 on: April 22, 2019, 07:51:09 AM »
|
|
|
Yes.
|
|
|
|
|
Logged
|
|
|
|
|
