Me7 bench setup - grounding pin resistor?

Pages: [1]

« previous next »

Author

Topic: Me7 bench setup - grounding pin resistor? (Read 2779 times)

vtraudt

Sr. Member

Karma: +4/-7
Offline

Offline

Posts: 377

	Me7 bench setup - grounding pin resistor? « on: April 22, 2019, 09:27:05 AM »

i bought a bench setup for flashing Me7 ecu.
Always had trouble getting ecu into boot mode, sometimes 10+ trial/error. Sometimes I just gave up.
This weekend, failed again to get ECU into boot mode.
Checked out the harness, continuity check with multimeter in 'beep' mode. Did NOT beep when tracing my ground "pin"/wire back to the ECU plug.
Thought broken wire. Took wire apart, and found a 220 Ohm resistor.

a) why did the seller add the resistor? Purpose?
b) is the resistor beneficial, or could it be the resistor has been causing my boot mode problems?


	Logged

2002 Allroad 2.7T 6spd stage 2
1998 A4 1.8T 5spd stage 3
1996 A4 2.8 auto stock

nyet

Administrator
Hero Member

Karma: +608/-168
Offline

Offline

Posts: 12270

	Re: Me7 bench setup - grounding pin resistor? « Reply #1 on: April 22, 2019, 09:50:34 AM »

He likely did it to provide a rudimentary current limiter so if you touched the grounding pin to something you shouldn't (e.g. +12 battery voltage) you don't fry something. It is possible it is interfering with getting into bootmode, but IMO unlikely (depending on which ECU, specifically.... ME7.1.1 ECUs can be dodgy to get into boot mode)


	Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex

vtraudt

Sr. Member

Karma: +4/-7
Offline

Offline

Posts: 377

	Re: Me7 bench setup - grounding pin resistor? « Reply #2 on: April 22, 2019, 10:21:46 AM »

Thanks. Will try without the resistor. But in principle a good idea (limiting the amps that flow if messing up. At 12V und 220 ohm, only 0.05 Amp should flow (50 mA), which may save components in case of a short. But not sure if the resistance would mess with ground the pin.


	Logged

2002 Allroad 2.7T 6spd stage 2
1998 A4 1.8T 5spd stage 3
1996 A4 2.8 auto stock

nyet

Administrator
Hero Member

Karma: +608/-168
Offline

Offline

Posts: 12270

	Re: Me7 bench setup - grounding pin resistor? « Reply #3 on: April 22, 2019, 10:26:19 AM »

depends entirely in input impedance (or pullup resistance). In theory, 220 ohms to ground should be a more than sufficient current sink.


	Logged

vtraudt

Sr. Member

Karma: +4/-7
Offline

Offline

Posts: 377

	Re: Me7 bench setup - grounding pin resistor? « Reply #4 on: April 22, 2019, 10:57:30 AM »

Quote from: nyet on April 22, 2019, 10:26:19 AM

depends entirely in input impedance (or pullup resistance). In theory, 220 ohms to ground should be a more than sufficient current sink.

Isn't (according to Mr. Ohm - The resistance R in ohms (Ω) is equal to the voltage V in volts (V) divided by the current I in amps (A)): I=U/R? here 12/220=-0.05


	Logged

2002 Allroad 2.7T 6spd stage 2
1998 A4 1.8T 5spd stage 3
1996 A4 2.8 auto stock

Pages: [1]

« previous next »

Jump to:

Navigation

Personal Tools

November 27, 2024, 06:52:09 AM

Welcome, Guest. Please login or register.
Did you miss your activation email?

Navigation

Personal Tools

Search