|
Jerry Tunin
|
 |
« on: April 25, 2019, 10:34:54 PM »
|
|
|
Unplugged solenoid.
CDNWS changed to 0.
KFNWSE whole table set to 18.
ESKONF AA FF 00 30 FF FB 30 changed to AA FF 00 30 FF FB 33
Copied KFZW to KFZW2 and KFZWOP to KFZWOP2.
Getting a P0010 - "A" Camshaft Position Actuator Circuit (Bank 1) now. Ideas?
|
|
|
|
|
Logged
|
|
|
|
aleks19411
Full Member
Karma: +4/-4
 Offline
Posts: 60
|
|
« Reply #1 on: April 26, 2019, 01:35:21 AM »
|
|
|
Translate these more cards to 18
KFNWSE, KFNWKHE, KFNWKRE — maps 16x8.
KFNWKHLLE
as well as the second esconf (there are two of them)
both before the card KFKHFM set the AA FF 00 30 FF F8 33
number of software would indicate
|
|
|
|
« Last Edit: April 26, 2019, 01:37:59 AM by aleks19411 »
|
Logged
|
|
|
|
|
BlackT
|
|
« Reply #2 on: April 26, 2019, 01:52:44 AM »
|
|
|
For AWT I only change CDNWS to 0.
I think ESKONF doesen't have relationship with that DTC.it is only when you have hardware DTC
|
|
|
|
|
Logged
|
|
|
|
|
Jerry Tunin
|
|
« Reply #3 on: April 29, 2019, 01:47:29 PM »
|
|
|
Update:
Unplugged solenoid.
CDNWS changed to 0.
KFNWSE, KFNWKHE, KFNWKRE, KFNWKHLLE change to 18.
Both ESKONF maps changed from AA FF 00 30 FF FB 30 to AA FF 00 30 FF FB 33.
Copied KFZW to KFZW2 and KFZWOP to KFZWOP2.
Getting a P0010 - "A" Camshaft Position Actuator Circuit (Bank 1) still.
This error code goes away if I plug back in the solenoid but eventually I'd like to install one that doesn't have the solenoid.
|
|
|
|
|
Logged
|
|
|
|
|
BlackT
|
|
« Reply #4 on: April 29, 2019, 01:57:35 PM »
|
|
|
Maybe your CDNWS is not at corect adress. Post jor ecu bin
|
|
|
|
|
Logged
|
|
|
|
aleks19411
Full Member
Karma: +4/-4
Offline
Posts: 60
|
|
« Reply #5 on: April 30, 2019, 12:36:58 AM »
|
|
|
Update:
Unplugged solenoid.
CDNWS changed to 0.
KFNWSE, KFNWKHE, KFNWKRE, KFNWKHLLE change to 18.
Both ESKONF maps changed from AA FF 00 30 FF FB 30 to AA FF 00 30 FF FB 33.
Copied KFZW to KFZW2 and KFZWOP to KFZWOP2.
Getting a P0010 - "A" Camshaft Position Actuator Circuit (Bank 1) still.
This error code goes away if I plug back in the solenoid but eventually I'd like to install one that doesn't have the solenoid.
Put the firmware here, we'll see. |
|
|
|
|
Logged
|
|
|
|
|
Jerry Tunin
|
|
« Reply #6 on: May 02, 2019, 10:29:44 PM »
|
|
|
Maybe your CDNWS is not at corect adress. Post jor ecu bin
Attached |
|
|
|
|
Logged
|
|
|
|
|
BlackT
|
|
« Reply #7 on: May 06, 2019, 06:38:36 AM »
|
|
|
CDNWS at 181AF
|
|
|
|
|
Logged
|
|
|
|
dal
Full Member
Karma: +6/-7
Offline
Posts: 210
|
|
« Reply #8 on: May 06, 2019, 07:49:03 AM »
|
|
|
For AWT I only change CDNWS to 0.
I think ESKONF doesen't have relationship with that DTC.it is only when you have hardware DTC
I have done the wideband conversion on my car. Mine was 512kb without VVT. I only got the STFT/LTFT functions to work after I disabled the VVT solenoid on ESKONF. In my case... |
|
|
|
|
Logged
|
|
|
|
|
Jerry Tunin
|
|
« Reply #9 on: May 09, 2019, 10:10:02 PM »
|
|
|
CDNWS at 181AF
Yeah that's the location I found it at too. Original value is 02 changed to 00. |
|
|
|
|
Logged
|
|
|
|
|
BlackT
|
|
« Reply #10 on: May 09, 2019, 10:53:01 PM »
|
|
|
For AWT I only change CDNWS to 0.
I think ESKONF doesen't have relationship with that DTC.it is only when you have hardware DTC
My bad i didn't read it well, that dtc is connected to ESKONF. Did you change second ESKONF? |
|
|
|
|
Logged
|
|
|
|
aleks19411
Full Member
Karma: +4/-4
Offline
Posts: 60
|
|
« Reply #11 on: May 14, 2019, 12:06:30 PM »
|
|
|
Yes. he wrote that he changed two eskonf
|
|
|
|
|
Logged
|
|
|
|
|
Jerry Tunin
|
|
« Reply #12 on: May 20, 2019, 09:55:42 PM »
|
|
|
My bad i didn't read it well, that dtc is connected to ESKONF. Did you change second ESKONF?
Yep |
|
|
|
|
Logged
|
|
|
|
|
