Pages: [1]
Author Topic: me7 95040.bin question  (Read 722 times)
mk5kid
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 7


« on: May 03, 2019, 08:18:07 AM »

i guys having some issues with my computer not reading my com port when im in the me7 95040 tool it opens the com where my obd cable is located and it tells me it was unable to open that com port but it gives me the baud rate im running windows 10 and using the ross tech cable with the intellig-boot mode off any ideas or tips would be great
Logged
nyet
Administrator
Hero Member
*****

Karma: +427/-53
Offline Offline

Posts: 9698


WWW
« Reply #1 on: May 03, 2019, 09:25:47 AM »

You need the VCP drivers to use the Ross-Tech with a COM port, as mentioned in the s4wiki
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
mk5kid
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 7


« Reply #2 on: May 05, 2019, 07:55:46 PM »

i did update my ross cable driver to the VCP driver update but still cant open the port to read eeprom im running windows im learning and new to this i have a read alot of posts onhere and trying my best thank you for answering my stupid questions lol
Logged
nyet
Administrator
Hero Member
*****

Karma: +427/-53
Offline Offline

Posts: 9698


WWW
« Reply #3 on: May 05, 2019, 09:02:04 PM »

did you enable vcp? did you assign a com port?
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
mk5kid
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 7


« Reply #4 on: May 14, 2019, 03:41:00 PM »

i did click on the box for vcp in the vcp properties menu but i dont how to assign the comport i see it says com port 0003 but the 95040 tool wont reconize the comport
Logged
mk5kid
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 7


« Reply #5 on: May 14, 2019, 04:07:22 PM »

i can use nefmoto just fine i can read full flash and write full flash no issus on that end
Logged
nyet
Administrator
Hero Member
*****

Karma: +427/-53
Offline Offline

Posts: 9698


WWW
« Reply #6 on: May 14, 2019, 04:21:35 PM »

You can adjust the com port in device manager -> Ports (COM & LPT)
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
mk5kid
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 7


« Reply #7 on: May 14, 2019, 05:46:14 PM »

i did some re installing of the vcp driver file and now my usb showed up in the port menu in device manager and its assigned com3 now thank you for your help sorta speak lol going to try to read the eeprom in a lil bit !
Logged
mk5kid
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 7


« Reply #8 on: May 14, 2019, 07:46:51 PM »

im back again and the 9540 tool is reading the com port but now im having a hard time putting my ecu in bootmode ive been grounding out pin24 for atleast 10 secs and even did 2-3 seconds also i get a messge saying bootmode ....fail...... no responce from ecu any ideas
Logged
Maxohio
Full Member
***

Karma: +2/-1
Offline Offline

Posts: 64


« Reply #9 on: May 14, 2019, 10:24:02 PM »

Are you using a test bench?
Logged
mk5kid
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 7


« Reply #10 on: May 16, 2019, 04:46:26 PM »

yes i am and finally got it into bootmode !
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.017 seconds with 18 queries. (Pretty URLs adds 0.001s, 0q)