Pages: [1] 2
Author Topic: 1.8t agu engine with 1.8t aum wiring and ecu > Incorrect Correlation  (Read 8776 times)
ulek3pl
Full Member
***

Karma: +8/-6
Offline Offline

Posts: 81



Hello! I do wiring swap in my agu (m3.8.3) to aum (me7.5). I use standard agu non vvt chain tens and cam sensor pulse wheel (4 gaps). What i need to vvt delete? I do:

CDNWS changed to 0.
KFNWSE whole table set to 18.
ESKONF
Copied KFZW to KFZW2 and KFZWOP to KFZWOP2.

And i have problem with incorrect corelation error and my car on 1 bar ride like crap.  Huh Huh Huh Huh
Do i need one gap cam sensor wheel?
Logged
grey
Full Member
***

Karma: +4/-1
Offline Offline

Posts: 146


« Reply #1 on: June 29, 2019, 01:59:28 AM »


i think this topic will help you;
http://nefariousmotorsports.com/forum/index.php?topic=1925.0
Logged
ulek3pl
Full Member
***

Karma: +8/-6
Offline Offline

Posts: 81


« Reply #2 on: June 29, 2019, 02:25:06 AM »

i see this, but i dont know do i need single or 4 gap cam sensor wheel on me7.5 with vvt disable :/
Logged
grey
Full Member
***

Karma: +4/-1
Offline Offline

Posts: 146


« Reply #3 on: June 29, 2019, 02:29:25 AM »

if you use a AGU head,you need agu cam sensor rotor
Logged
ulek3pl
Full Member
***

Karma: +8/-6
Offline Offline

Posts: 81


« Reply #4 on: June 29, 2019, 02:44:13 AM »

agu and aum rotor are the same (4 gap) and i have this error alredy. Cam hall sensor in agu and aum i think is the same.  I chcek timing today maybe it jump  Huh But before wiring swap car run fine near 300 hp.
Logged
grey
Full Member
***

Karma: +4/-1
Offline Offline

Posts: 146


« Reply #5 on: June 29, 2019, 02:52:22 AM »

my a friend installed ME7.5 Ecu to AGU engine.But he hasn't any issue with incorrect correlation
Logged
ulek3pl
Full Member
***

Karma: +8/-6
Offline Offline

Posts: 81


« Reply #6 on: June 29, 2019, 02:55:24 AM »

Maybe timing jump off in same time. I check this today. Your friend do something with maps eskonf etc?
Logged
grey
Full Member
***

Karma: +4/-1
Offline Offline

Posts: 146


« Reply #7 on: June 29, 2019, 03:00:46 AM »

I think it is mechanical,yes ESKONF tuning and CDNWS
After about timing maps..
Logged
BlackT
Hero Member
*****

Karma: +79/-39
Offline Offline

Posts: 1415



« Reply #8 on: June 29, 2019, 04:17:49 AM »

http://nefariousmotorsports.com/forum/index.php?topic=15645.15
Start from last post in this page

You need 4 gap cam rotor, what DTC you get?
Logged
ulek3pl
Full Member
***

Karma: +8/-6
Offline Offline

Posts: 81


« Reply #9 on: June 29, 2019, 04:51:10 AM »

I have 4 gap sensor. Errors in attachment and readiness from 90,93.
Logged
Blazius
Hero Member
*****

Karma: +89/-40
Offline Offline

Posts: 1277



« Reply #10 on: June 29, 2019, 05:07:48 AM »

Holy , 17 kw cf idle stab is most definitly not good. Check your timing first. You need to use the VVT and the rotor and the sensor from the new head if you want VVT. You can code out VVT if you want but why when its there?

I am running AEB head with AEB cams and vvt.
« Last Edit: June 29, 2019, 05:24:43 AM by Blazius » Logged
ulek3pl
Full Member
***

Karma: +8/-6
Offline Offline

Posts: 81


« Reply #11 on: June 29, 2019, 05:14:10 AM »

i dont need vvt. I want use my agu non vvt chain tens. All run fine before wiring swap. I check timing and chain later.
Logged
BlackT
Hero Member
*****

Karma: +79/-39
Offline Offline

Posts: 1415



« Reply #12 on: June 29, 2019, 05:16:57 AM »

Same problem I have,
Bad timing friend
Logged
ulek3pl
Full Member
***

Karma: +8/-6
Offline Offline

Posts: 81


« Reply #13 on: June 29, 2019, 10:46:38 AM »

Problem solved. Timing belt is cutted at half and jump one tooth.  Shocked Shocked
Logged
Blazius
Hero Member
*****

Karma: +89/-40
Offline Offline

Posts: 1277



« Reply #14 on: June 29, 2019, 10:51:40 AM »

lol
Logged
Pages: [1] 2
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.044 seconds with 16 queries. (Pretty URLs adds 0s, 0q)