Pages: [1]
Author Topic: 1.8t BAM engine aux/secondary water pump wiring?  (Read 3065 times)
tao13
Sr. Member
****

Karma: +16/-46
Online Online

Posts: 460


« on: July 21, 2019, 06:26:56 AM »

Hi all.
Anybody can help me with this information about 1.8t BAM engine aux/secondary water pump wiring?
From where this pump receives signal , from ECU or from radiator fans thermocuple?
Many thanks in advance
Logged
fknbrkn
Hero Member
*****

Karma: +176/-18
Offline Offline

Posts: 1401


mk4 1.8T AUM


« Reply #1 on: July 21, 2019, 06:41:40 AM »

From coolant fan relay module (under the battery)
Logged
tao13
Sr. Member
****

Karma: +16/-46
Online Online

Posts: 460


« Reply #2 on: July 28, 2019, 09:54:05 PM »

Many thanks fukenbroken
So it works at the same time with fans(after 97-98 degree) when the ignition is on and after ignition is cut , only when the fans are runing, correct?
I found some post on the other sites where people said the aux pump works 10 minutes , but it is hard to belive that.
Have a good day.
« Last Edit: July 28, 2019, 09:58:08 PM by tao13 » Logged
adam-
Hero Member
*****

Karma: +122/-33
Offline Offline

Posts: 2177


« Reply #3 on: July 28, 2019, 11:55:09 PM »

Why is it hard to believe?  It's to circulate coolant when the engine isn't running, not aid it when it is.
Logged
fknbrkn
Hero Member
*****

Karma: +176/-18
Offline Offline

Posts: 1401


mk4 1.8T AUM


« Reply #4 on: July 29, 2019, 05:45:57 AM »

It works when ignition is on and 10 mins after ign off
No matter of temp and fans here
Logged
tao13
Sr. Member
****

Karma: +16/-46
Online Online

Posts: 460


« Reply #5 on: July 29, 2019, 10:05:17 PM »

ok and thanks again , but the coolant fans works after ignition is off only few minutes not 10 minutes , did i wrong?
Logged
vladvlad
Full Member
***

Karma: +1/-73
Offline Offline

Posts: 138


« Reply #6 on: June 14, 2022, 10:41:59 AM »

Anybody know coolant fan relay module from BAM(with auxiliary water pump) is different than AUQ/AUM(without auxiliary water pump)? I think they must be different because ecu must knows to open/close a different relay/timmer for this water pump.
From ecu to auxiliary water pump on BAM is not any connections/wires.
Logged
aef
Hero Member
*****

Karma: +69/-46
Offline Offline

Posts: 1566


« Reply #7 on: June 14, 2022, 10:54:47 PM »

There are alot of revisions of the 1J0919506*

Have a look at yours or the pictures in google. If you see WP written on one Pin then it will support the Waterpump.
Logged
tao13
Sr. Member
****

Karma: +16/-46
Online Online

Posts: 460


« Reply #8 on: June 16, 2022, 11:28:41 AM »

Hi and thanks AEF. I checked the wires from my old skoda octavia 1 with AUM engine. It had 1J0919506K on it and i saw all wires are connected in this 1J0919506, but the ar not had seconbdary water pump. I thinked it must not had an wire plugged in pin 1 - WP from 14pins connector of 1J0919506. this wire must goes in water pump, right?
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.017 seconds with 16 queries. (Pretty URLs adds 0s, 0q)