NefMoto > Noob Zone > Noob Questions (Moderator: turboat) > I need urgent help pleaasee help!!!
Pages: [1]
« previous next »
Author Topic: I need urgent help pleaasee help!!!  (Read 3953 times)
emral2001
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 5
« on: July 27, 2019, 05:07:00 AM »
Hello , i have a audi a4 2002 1.8t BFB 163 hp 8E0909018A ecu, flashed 8N0906018AB file into it but flashed the wrong file without corrected checksums and now car cranks and wont start cant connect to nefmoto and vcds disconnected battery didnt help
Logged
BlackT
Hero Member
*****

Karma: +79/-40
Offline Offline

Posts: 1425
« Reply #1 on: July 27, 2019, 07:19:07 AM »
You need Galleto 1260 and connect in boot mode, then upload correct file
Logged
emral2001
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 5
« Reply #2 on: July 27, 2019, 07:55:51 AM »
can i do it with a normal vag com - hex - can - usb cable i dont have a galletto cable and i need to fix it fast its weekend cant get a new cable right now
Logged
Blazius
Hero Member
*****

Karma: +89/-40
Offline Offline

Posts: 1282
« Reply #3 on: July 27, 2019, 01:58:33 PM »
Quote from: emral2001 on July 27, 2019, 07:55:51 AM
can i do it with a normal vag com - hex - can - usb cable i dont have a galletto cable and i need to fix it fast its weekend cant get a new cable right now

Nope. well not really. You need to bootmode debrick the ecu, so you need a setup for it aswell. You can also only use that cable if it has the correct chip and rest of the components to do bootmode flashing, and you probably dont have a genuine rosstech cable.
Logged
emral2001
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 5
« Reply #4 on: July 27, 2019, 02:01:12 PM »
Can you tell me more about this i have the genuine one what software do i need i am about to do bench boot mode right now
Logged
adam-
Hero Member
*****

Karma: +124/-33
Offline Offline

Posts: 2179
« Reply #5 on: July 27, 2019, 04:48:11 PM »
You need to learn not to flash files you didn't make nor have any idea about.
Logged
Blazius
Hero Member
*****

Karma: +89/-40
Offline Offline

Posts: 1282
« Reply #6 on: July 27, 2019, 04:53:21 PM »
Quote from: emral2001 on July 27, 2019, 02:01:12 PM
Can you tell me more about this i have the genuine one what software do i need i am about to do bench boot mode right now

I am sorry, but you cannot do bootmode flashing in like 10 mins. You need to build a bootmode setup, there are many guides for this search the forum, but atleast you will need to be able to solder, get a power supply, an obd2 connector and some other stuff aswell.

You will also have to modify the galleto software to work with the ftdi chip , or use some other software to do the flashing. Again just use the search bar on the left.


Also why did you flash a TT chassis file onto a b6 chassis ecu ?
« Last Edit: July 27, 2019, 04:55:02 PM by Blazius » Logged
_nameless
Hero Member
*****

Karma: +342/-466
Offline Offline

Posts: 2802
« Reply #7 on: July 27, 2019, 05:23:15 PM »
you can bootmode flash in the car. just disconnect the ground wire short boot pin on ecu. with the key in the on position reconnect the battery and rewrite threw the port  in bootmode. done it several times works without an issue
Logged
Giving your mom a tuneup
BlackT
Hero Member
*****

Karma: +79/-40
Offline Offline

Posts: 1425
« Reply #8 on: July 27, 2019, 11:08:02 PM »
Quote from: Marty on July 27, 2019, 05:23:15 PM
you can bootmode flash in the car. just disconnect the ground wire short boot pin on ecu. with the key in the on position reconnect the battery and rewrite threw the port  in bootmode. done it several times works without an issue
And also when doing boot mode in car, you must remove ECM relay or smaler conector on ECU.  I have problem that some ECU-s won't go in boot mode when pin 121 is geting power
Logged
emral2001
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 5
« Reply #9 on: July 28, 2019, 03:30:51 AM »
Quote from: adam- on July 27, 2019, 04:48:11 PM
You need to learn not to flash files you didn't make nor have any idea about.
Yeah i know i didnt realise,

Found the post that cloned serial from the galletto program to the cable tried that galletto connected but says boot mode inactive i am grounding pin 24 first then connecting the - terminal on the battery after 2-3 seconds i let go the ground cable from the pin but no success Sad gonna try with a different laptop but there's no logic in that i cant enter boot mode or i cant do that i dont know
Logged
emral2001
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 5
« Reply #10 on: July 28, 2019, 03:31:29 AM »
Quote from: BlackT on July 27, 2019, 11:08:02 PM
And also when doing boot mode in car, you must remove ECM relay or smaler conector on ECU.  I have problem that some ECU-s won't go in boot mode when pin 121 is geting power

Tried this still didnt do it
Logged
prj
Hero Member
*****

Karma: +1072/-485
Offline Offline

Posts: 6041
« Reply #11 on: July 28, 2019, 05:58:28 AM »
Disconnecting ground wire is potentially dangerous.
If the ECU is grounded anywhere on chassis and then you short the flash chip pin to ground before having main ground in the ECU, it can kill the processor.
It 100% kills the processor if you ground the boot pin directly to chassis before grounding the ECU.

It should be always power that is removed, never ground.
« Last Edit: July 28, 2019, 06:00:36 AM by prj » Logged
PM's will not be answered, so don't even try.
Log your car properly - WinOLS database - Tools/patches
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 30, 2024, 12:03:00 PM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.02 seconds with 17 queries. (Pretty URLs adds 0.001s, 0q)