NefMoto > Technical > Tuning > Tuning PID on 8E0 ECUs
Pages: 1 [2]
« previous next »
Author Topic: Tuning PID on 8E0 ECUs  (Read 9032 times)
BlackT
Hero Member
*****

Karma: +79/-40
Offline Offline

Posts: 1425
« Reply #15 on: October 11, 2019, 11:42:57 PM »
Can you explain why?
Logged
fknbrkn
Hero Member
*****

Karma: +186/-24
Offline Offline

Posts: 1460


mk4 1.8T AUM
« Reply #16 on: October 12, 2019, 07:46:12 AM »
You solve 1 specific problem (@wot on a third gear in mid range rpm) by the hard limiting of kfldrl
Thus works only with these conditions
And linear drl goes pretty well on a big turbos with ext wg but not in this case
Logged
BlackT
Hero Member
*****

Karma: +79/-40
Offline Offline

Posts: 1425
« Reply #17 on: October 12, 2019, 11:29:23 AM »
Not true, it work realy well so far. No mather what gear, what RPM and how much throotle.  Real real smooth and responsive boost in every area
Logged
prj
Hero Member
*****

Karma: +1072/-487
Offline Offline

Posts: 6045
« Reply #18 on: October 12, 2019, 12:07:03 PM »
You might as well run it off of LDRAPP.
It's pretty much open loop at this point.
Logged
PM's will not be answered, so don't even try.
Log your car properly - WinOLS database - Tools/patches
BlackT
Hero Member
*****

Karma: +79/-40
Offline Offline

Posts: 1425
« Reply #19 on: October 12, 2019, 12:48:51 PM »
I want to do it right way. No cheat, even if it is working right. I will do some more research about ME7 PID. Then try to tune it again
Logged
soul87
Jr. Member
**

Karma: +5/-0
Offline Offline

Posts: 44
« Reply #20 on: October 12, 2019, 09:51:11 PM »
Imx and ldr maps looks strange... You want 95 dc n75 everytime at spool... Also maps should be somehow smooth and linear... You are setting 95dc at spool for 1000mbar and 80dc at 1300... Ldr map Also is not linear... Bad idea
Logged
BlackT
Hero Member
*****

Karma: +79/-40
Offline Offline

Posts: 1425
« Reply #21 on: October 13, 2019, 05:38:49 AM »
Quote from: soul87 on October 12, 2019, 09:51:11 PM
Imx and ldr maps looks strange... You want 95 dc n75 everytime at spool... Also maps should be somehow smooth and linear... You are setting 95dc at spool for 1000mbar and 80dc at 1300... Ldr map Also is not linear... Bad idea
I didn't bordet with that region beacuse in low RPM turbo can't open WG, so i the same what DC is it

Yes, but with this seting on actuator i have huge spike on 95% DC . It must be limited whey before the turbo get close to desired boost.  80% or 95% when this little turbo spool up, the diffrence in spool speed is insignificant. And I like more this linear spool at little lower DC, the car is nicer to drive

But I will try with RS4 values for IMX and LDR to see what will hapen
Logged
Pages: 1 [2]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • December 03, 2024, 01:19:26 PM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.015 seconds with 16 queries. (Pretty URLs adds 0s, 0q)