Pages: [1]
Author Topic: EDC15 IMMO  (Read 11852 times)
240sxpooter
Jr. Member
**

Karma: +5/-1
Offline Offline

Posts: 32


« on: March 16, 2012, 08:59:13 AM »

 Has anyone preformed a De-Immo on a EDC15VM+?

038906012GN
Diesel EDC15VM+ 4308
0281011034

 I'm willing to pay for a working solution.
 
    Cheers
Logged
littco
Hero Member
*****

Karma: +52/-7
Offline Offline

Posts: 903


« Reply #1 on: March 16, 2012, 10:55:48 AM »

can i just asked how you read this please.
Logged
BDK
Jr. Member
**

Karma: +2/-0
Offline Offline

Posts: 28


« Reply #2 on: March 16, 2012, 04:49:39 PM »

There's a free downloadable utility on the abritus72 (vag commander) website. I haven't personally tried it though. 
Logged
240sxpooter
Jr. Member
**

Karma: +5/-1
Offline Offline

Posts: 32


« Reply #3 on: March 19, 2012, 06:42:39 AM »

can i just asked how you read this please.

 With a chip reader. Does the file look corrupt?
Logged
SundayNightDriver
Jr. Member
**

Karma: +9/-1
Offline Offline

Posts: 25


« Reply #4 on: March 29, 2012, 04:16:17 AM »

I have a similar dump with immo on + off. Byte 01b0 and 01de (value 0x73 in your dump) were changed from 0x60 to 0x33 there. The pages have no CRCs. Try changing the two bytes to 33.
Logged
hans j
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 7


« Reply #5 on: September 17, 2012, 05:57:38 PM »

With a chip reader. Does the file look corrupt?


Did you desolder this then? There are a few programs out there that will supposedly switch immo on and off and I can load this file and read VIN, IMMO and KM and supposed to be able to switch IMMO on or off.

I have been trying to find a way to get the .bin file off my ecus so I can drive my diesel swap.
Logged
NMS
Full Member
***

Karma: +6/-3
Offline Offline

Posts: 50


« Reply #6 on: September 17, 2012, 08:44:02 PM »

IMMO OFF solution:

Address 1B0 from 73 -> 60
Address 1DE from 73 -> 60

Attached IMMO off file.


Edit: Shit, just noticed this is an ancient thread. Sorry for bumping, saw hans post, thought it was a fresh thread.
Logged
hans j
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 7


« Reply #7 on: September 18, 2012, 12:17:16 PM »

Thanks for the file, I'm still fighting how to get the .bin off the ecu. My ebay galletto cable is on it's way though!

I have 012FD, 012FF and 012CP (IMMO2) ecu's to play with, just need more time to mess with the settings on nefmoto to see if it will work.
Logged
NMS
Full Member
***

Karma: +6/-3
Offline Offline

Posts: 50


« Reply #8 on: September 18, 2012, 07:03:57 PM »

Thanks for the file, I'm still fighting how to get the .bin off the ecu. My ebay galletto cable is on it's way though!

I have 012FD, 012FF and 012CP (IMMO2) ecu's to play with, just need more time to mess with the settings on nefmoto to see if it will work.

It won't. These tools are for reading FLASH only. You want to buy a tool called "UPA-USB" by Elrasoft. That will read/write eeproms. Or a GQ-3X which will do both, but you will need to adapters, as well as soldering stations + hot air station.
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.018 seconds with 16 queries. (Pretty URLs adds 0s, 0q)