NefMoto > Noob Zone > Noob Questions (Moderator: turboat) > What do I need to exchange CPUs in my Audi A4 1.8TQ B6
Pages: [1]
« previous next »
Author Topic: What do I need to exchange CPUs in my Audi A4 1.8TQ B6  (Read 3311 times)
romfeo
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 4
« on: November 05, 2019, 06:14:28 AM »
Hi there,

Total noob here.

I have an Audi A4 1.8TQ B6.
ECU is 8E0 909 518 AA /  0 261 207 934 and it has an MTM chip on it

After some water damage to the ECU box my car is not working properly. It is underpowered, has difficulty to start and in VAG-COM I get 16985 - Internal Control Module: Memory Check Sum Error
P0601 - 001 - Upper Limit Exceeded

Everybody is telling me that I need a new ECU.

Case 1: I can get some "plug and play" ECUs from Ebay for around 200 euros but I honestly cannot afford that. I have no work at the moment and this car is the only we have in the family to take kids to school etc.

Case 2: On the other hand, I can get the same ECU as mine for around 50 euros. but I guess it wouldn't work because of the immobilizer, is that correct?

So, If I get the ECU from Case 2, what needs to I need to follow in order for my car to work (as stock of course, I don't care about the MTM). Can anybody please point me to the right direction?
Logged
_nameless
Hero Member
*****

Karma: +342/-466
Offline Offline

Posts: 2801
« Reply #1 on: November 05, 2019, 06:21:46 AM »
You have a few options. You can adapt the new ecu keeping the immo active. A bit involved and need a few programs to do this. The other way is to make a bench flash setup and read and write the eeprom on the bench you can read your original eeprom and write it to the new ecu or just immo off and write it back. The most straightforward way would be to remove the st95040 chip from your original and move it to your new ecu
Logged
Giving your mom a tuneup
romfeo
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 4
« Reply #2 on: November 05, 2019, 06:28:48 AM »
Quote from: Marty on November 05, 2019, 06:21:46 AM
You have a few options. You can adapt the new ecu keeping the immo active. A bit involved and need a few programs to do this. The other way is to make a bench flash setup and read and write the eeprom on the bench you can read your original eeprom and write it to the new ecu or just immo off and write it back. The most straightforward way would be to remove the st95040 chip from your original and move it to your new ecu

So I guess the st95040 holds the immobilizer information.... and If I move that chip from the old cpu to the new, it will just work? No other programming is needed?
Logged
fluke9
Full Member
***

Karma: +26/-1
Offline Offline

Posts: 113
« Reply #3 on: November 05, 2019, 07:35:20 AM »
Quote from: romfeo on November 05, 2019, 06:28:48 AM
So I guess the st95040 holds the immobilizer information.... and If I move that chip from the old cpu to the new, it will just work? No other programming is needed?

If it has the same software version or eeprom layout did not change between software versions (in 99% of all cases its the same for a given Bosch HW-Nr.).
So yes, just swap that little 8 pin SOIC over and you are good to go.
Logged
BlackT
Hero Member
*****

Karma: +79/-40
Offline Offline

Posts: 1425
« Reply #4 on: November 05, 2019, 07:45:41 AM »
Where are you from?
Logged
romfeo
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 4
« Reply #5 on: November 05, 2019, 08:55:34 AM »
Greece
Logged
romfeo
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 4
« Reply #6 on: November 05, 2019, 08:56:30 AM »
Would this procedure described in the video by Ross tech work, if i have both pins for both ecus?

https://www.youtube.com/watch?v=J5_51qeEyec
Logged
BlackT
Hero Member
*****

Karma: +79/-40
Offline Offline

Posts: 1425
« Reply #7 on: November 05, 2019, 09:04:14 AM »
I can send you immo off ecu for 60-70€ + shipping
Logged
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 25, 2024, 12:32:49 PM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.017 seconds with 17 queries. (Pretty URLs adds 0s, 0q)