NefMoto > Noob Zone > Noob Questions (Moderator: turboat) > IMX for GT2871r
Pages: 1 2 3 [4]
« previous next »
Author Topic: IMX for GT2871r  (Read 15911 times)
vvt18
Full Member
***

Karma: +2/-74
Offline Offline

Posts: 139
« Reply #45 on: April 18, 2020, 09:11:05 AM »
LTFT is in actual configuration at 20 outside degree between -1.5 and -0.8!
Can i decrease a little krkte or tvub for last 3 values,
I read on forum many settings of 550 bosch injectors at 3 bars.
I put my own like i wrote in previous post.
Happy Easter to all!
« Last Edit: April 18, 2020, 09:13:24 AM by alin1 » Logged
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12268


WWW
« Reply #46 on: April 18, 2020, 09:17:21 AM »
then i'd say you're good.

Figure out the hardware side of your fueling issues first, then go from there, since it means you're running out of fuel at higher loads/rpms, and not because of the tune.
Logged
ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
vvt18
Full Member
***

Karma: +2/-74
Offline Offline

Posts: 139
« Reply #47 on: April 18, 2020, 09:23:53 AM »
Thanks Nyet and AEF too.
Both of you advice me it's a hardware problem.
I will try to put an aux outlet fuel pump after original one from reservoir.

PS: about kvb i can put directly 550 value like my injectors capacity or must put a 480 value calculated?
Thanks again.
« Last Edit: April 18, 2020, 09:26:55 AM by alin1 » Logged
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12268


WWW
« Reply #48 on: April 18, 2020, 09:28:06 AM »
Quote from: alin1 on April 18, 2020, 09:23:53 AM
Thanks Nyet and AEF too.
Both of you advice me it's a hardware problem.
I will try to put an aux outlet fuel pump after original one from reservoir.

PS: about kvb i can put directly 550 value like my injectors capacity or must put a 480 value calculated?
Thanks again.

In my experience KVB is never right w/o trial and error tuning. Not sure why.
Logged
ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
vvt18
Full Member
***

Karma: +2/-74
Offline Offline

Posts: 139
« Reply #49 on: April 18, 2020, 09:36:12 AM »
In this case i left 550.

THANKS!
Logged
Pages: 1 2 3 [4]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 24, 2024, 01:27:11 AM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.016 seconds with 17 queries. (Pretty URLs adds 0.001s, 0q)