the maps are located in different spots on all the different ecu's, so you must find where these different addresses are and modify the xdf.

i would use the mbox xdf as a base to modify off of. 

Good luck.

How do you go about doing the disassembling??? I need to code out my EGT's on my AA box and don't know how to see where they are. I am using tunerpro and have already downloaded the .bin file from my car.

josh

EDIT here is my bin file if anyone wants to play with it... this is also a GIAC-X tuned ECU.

I posted all the info for removing the EGT's on an AA box ecu in another thread. With all the memory offsets and what not.

I thought i already modded your file for you at some point no?

anyways, i have a AA box def file started.  and i thought i sent it to you?  or less someone else had the same request at some point.  Id have to dig up those mods.


And the method i use for finding maps in Winols since tunerpro is garbage to me.  I load up a stock euro .bin with the a2l file for it, I then search through code comparing and finding maps.  pretty easy for the larger maps, single values can be a pain at times.  and if you cannot find the maps, then off to dissas. the file

ive only had trouble with maybe 10-15% of my def file so far.  Ive only got maybe 40-50 maps found though, but they are the important ones you need to tune.

in all honesty, its easier to use the euro file with the a2l if you dont want to find the maps.  I loaded it up and it works fine, its all in german, but you will quickly learn german and the terms as they are re-used tons in the file.  And having some bosch documentation on me7 helps

Yeah I would like to compare the maps and see whats different.But there is not descriptions or information on what maps are at what addresses and what function they perform.I have no problem going through the maps problem is comparing maps,not knowing what each map does.Anyone have a list???Or at least a few??I believe to successfully tune only about 8-10maps need to be adjusted if i remember correctly.

What is it you are looking for?  A list of L box data offsets?

Right, here it is:

Format:  Description (Bosch Name), bytes of axes before data starts, internal address of object

These addresses are where the program starts reading data and there may be additional axis data in front of the actual map.  My code looks at it from the ME7 binary perspective, and if ME7 reads the axis at the same time so do I.  You should be able to see in winols, axis often have a length followed by the axis.  Axes and maps can be 8 or 16 bits wide, if the axis is 16bit then so are the lengths.

To change the internal address to a file offset just remove the most significant 8 bits, ie the 0x8 at the start.  When there are axis data points that my code has recognised, just add them to the offset to skip over the axis.  *NB* The axis information is a new feature and as such it only deals with a handful of situations - so there are some zeros when there should be additional data.
 

Above all else please remember that this is machine generated data.  I've not checked it, not even looked at it.  Please look in winols and verify each one before you rely upon it. The program is usually right, but if it's wrong any constructive feedback would be appreciated.



SLOGIN (preceed login with a 0),0,0x812122
KLOGIN (preceed login with a 0),0,0x812120
Table:Normalized mass flow over DK (KFMSNWDK),48,0x811198
Correction factor for combustion chamber pressure at NWS active (KFPBRKNW),44,0x81b976
Correction factor for combustion chamber pressure (KFPBRK),44,0x81b882
Table: target load KFMIRL,60,0x811950
Inverse pedal map for cruise control (KFWPFGR),60,0x81b510
Cold start enrichment factor (FKSTT_1_A) NON STANDARD ACCESS, MANUAL DECODE REQUIRED,0,0x811d6c
 Delta pressure for overboost protection diagnosis (KFDLULS),18,0x819781
Lambda - driver desired LAMBDA,0,0x81c05c
MAF_correction_table_KFKHFM,30,0x814edb
Pedal angle threshhold for compressor shutoff,0,0x816171
delta lambda for component protection DLBTS,0,0x81c13f
Desired idle engine speed while cat heating with drive engaged KFNFSKHM,0,0x81c330
Characteristic curve for continuous limit value control (fr) (FQTEFR),0,0x81e891
Injection correction during RLFS (FRLFSDP),0,0x81bfb8
Maximum specified load IAT correction factor map (KFTARX),0,0x81d820
Maximum engine speed on speed signal error detection (automatic transmission)? (NMAXDVG),0,0x817036
Weighting factor for slow boost pressure intervention on rlmax via KR (KFFWLLDE),0,0x81d7a0
Factor for rapid LDR intervention (reduction) (KFFSLDE),0,0x81d720
Factor for slow LDR intervention on rlmax via KR (KFFLLDE),0,0x81d6a0
Factor for boost pressure intervention through KR (KFFLDEO),0,0x81d620
LDR-control parameter Q1 in stationary operation (integration coefficient) (LDRQ1ST),0,0x81d5e8
LDR-control parameter Q1 in dynamic operation (integration coefficient) (LDRQ1DY),0,0x81d5c8
LDR-control parameter Q0 (LDRQ0DY),0,0x81d5a6
LDR-control parameter Q2 (KFLDRQ2),0,0x81d53c
Map for linearization of boost pressure N75? (KFLDRL),0,0x81d3fc
LDR I-Regulator limit (KFLDIMX),0,0x81d2aa
Enrichment on ignition retard (KFLAMKRL),0,0x818e12
RPM Axis for Timing (words),0,0x81009a
Load Axis for Timing (words),0,0x8142b4
Optimal ignition angle (KFZWOP),0,0x815603
Axis: Ignition Timing(load),0,0x812f6e
Optimal ignition angle variant2 (KFZWOP2),0,0x8156b3
Maximum engine speed for throttle body motor backup operation (NMXDAEF),0,0x815765
Allowable torque on afterstart extension (KFMIZUNS),0,0x8157ba
Allowable indicated torque to torque limit before filter (KFMIZUFIL),0,0x81577a
Map with permanent latest possible ignition angle (KFZWMS),0,0x815d8d
Ignition angle map (KFZW),0,0x815f0f
Ignition angle map (KFZW2),0,0x815e4f
Axis: RPM (PID),0,0x810078
Axis: RPM (misfire detection),0,0x8100bc
Maximum specified load IAT correction factor map under continuous knock (KFTARXZK),0,0x81d8a0
AXIS: Unknown, maybe IAT,0,0x814357
Maximum specified load during continuous knock (LDRXNZK),0,0x81d962
Maximum specified load (LDRXN_1_A),0,0x81d920
Load threshold for surge recognition for misfire recognition attenuation (RLSALUN),0,0x81469a
Upper load curve for DKAT active _RLDKTSO_0_A,0,0x814bf8
*Rough running deviation (dluts) reference value (KFDLUR),0,0x814594
*Rough running deviation (dluts) reference value 2 (KFDLUR2),0,0x814614
*Rough running deviation (dluts) reference value 1 (KFDLUR1),0,0x8145d4
Misfire detection: RPM deviation fade-out threshold (NGALU),0,0x8101e8
map_Optimal_torque_under_monitoring_KFMI_UM,0,0x814098
Axis:for_KFMI_UM+KFZW_UM,0,0x81407d
map_Optimal_ignition_angle_under_monitoring_KFZW_UM,0,0x8140d8
map_Offset_tolerance_depending_on_allowed_torque_KFMDZOF_UM,0,0x814129
Map for allowable torque from pedal position in the functions monitoring (KFMPED_UM),0,0x814169
Map for allowable torque from pedal position on cold motor (KFMPNS_UM),0,0x8141a9
MAF linearization (MLHFM),0,0x810d74
Table: Repeated cold start factor of start count reduction KFWKSTAB,0,0x811d92
Table: Delta ignition angle with tip engaged DZWTIN,0,0x811f38
Table: Desired pressure ratio DK dynamic KFVPDKSD,0,0x8121b2
Table: Desired pressure ratio stationary KFVPDKSE,0,0x8122d2
Axis: RPM for KFVPDKSD and KFVPDKSE,0,0x8100d8
Table: Starting torque (KFMDST_0_A),0,0x81251c
Table: Relative torque request from pedal KFPED_0_A,0,0x812aba
Table: Optimal engine torque map (KFMIOP),0,0x812e0e
Table: Lambda linearization; sensor behind cat (LALIUSH),0,0x81321c
Table: Minimum ignition angle KFZWMN,0,0x813436
Table: Minimum ignition angle for start and warm up KFZWMNST,0,0x81349c
Axis: RPM(knock regulation),0,0x81825f
Axis: Load (unknown use),0,0x81828a
Axis: Load(EGT enrich),0,0x8182af
EMBP correction of the secondary air mass (KFFMSML_0_A),0,0x818358
Weight of ftbr dependent on IAT (FWFTBRTA),0,0x818801
Weighting factor Tans/Tmot for combustion temperature model KFFWTBR,0,0x81881e
Map for variable cam timing KFNW,0,0x8188f4
Map for variable cam timing during warmup KFNWWL,0,0x81896a
Lambda map at partial load (KFLF),0,0x818a23
Injection cutoff angle (KFWEE),0,0x818b55
Injection cutoff angle (cold) (KFWEEK),0,0x818b95
Factor delta desired lambda for component protection (KFFDLBTS_0_A),0,0x818fac
Desired Lambda for component protection (KFLBTS_0_A),0,0x81906c
Delta angle knock regulation offset for average retard (DWKRMSN),0,0x819473
Knock regulation delta - angle safety (KRDWSN),0,0x8194b9
Ignition retard per knock event (KRFKLN),0,0x8194c9
Maximum ignition retard (KRMXN),0,0x8194d9
TV correction due to altitude effect on ambient pressure (KFLDIOPU),0,0x819597
Map for weighting factor of reference boost pressure as a function of IAT (KFWPLGTA),0,0x8195d7
LDR I-Regulator limit correction as a function of IAT (LDIATA),0,0x81961c
Delta load (rl) under overboost condition (KFLDRXO),0,0x819642
Down regulation interval for LDR overboost (TABLDOBN),0,0x819670
Time for LDR overboost active (TLDOBAN),0,0x819678
 Off time for overboost (TLDOBN),0,0x819680
 LDR altitude limitation (maximum pressure ratio) (KFLDHBN),0,0x8196a4
 Maximum load at E_ldo LDR (overboost error) (LDORXN),0,0x8196e4
 LDR pressure limit at too high a temperature engine (LDPBN),0,0x8196ec
 rl threshold for slow LDR-intervention (adaptation) (RLKRLDA),0,0x8196f4
 Map for LDR application without Md-coordination (KFLDRAPP),0,0x8196fc
Maximum permissible pressure ratio DK for ldra diagnosis? (KFVPDKLD),0,0x8197d3
Motor temperature dependent delay time for drive in (R) (TVFSREM),0,0x819983
Characteristic curve for tmot; upper rL control limit for controller before Kat (RLLRTMO),0,0x819dfe
closing time (from RPM; V) (KFSZT),0,0x81a282
closing time (from load; RPM) (KFTSRL),0,0x81a2d4
Threshold for B_minflr diagnosis HFM/HLM (KFMLDMN),0,0x81b71e
Threshold for B_maxflr diagnosis HFM/HLM (KFMLDMX),0,0x81b7c2
Factor for maximum pressure ratio with auxilliary load signal  (FPVMXN2),0,0x81b868
Internal exhaust partial pressure dependent on cam adjustment when sumode=0 (KFPRG),0,0x81ba6a
Conversion constant for ps->rl dependent on cam adjustment when sumode=0 (KFURL),0,0x81bb06
Desired idle speed when in gear (NFSM),0,0x8198e6
Weighting map for cold start factor (KFWKSTT),0,0x815168
Warm up enrichment factor (KFFWL_0_A),0,0x818c7b
Warm up enrichment factor (KFFWL_1_A),0,0x818d0b
Default throttle plate angle from charge signal (KFWDKPP),0,0x814c4e
Maximum throttle plate angle for plausibility with load signal (WDKPMXN),0,0x814d13
Min delta pressure before throttle plate for wastegate diagnosis (DPVDKDWG),0,0x816f9e
Axis: for Min delta pressure before throttle plate for wastegate diagnosis (DPVDKDWG),0,0x816f95
Max delta plsol for wastegate diagnosis (DPLSDWG),0,0x816f84
Axis: for Max delta plsol for wastegate diagnosis (DPLSDWG),0,0x816f7b
Delta timing during warmup,0,0x816018
Delta timing during warmup,0,0x816018
Correction factor for fuel supply system (FKKVS),0,0x81bd42
Desired idle speed (NLLM),0,0x8198e6
desired throttle plate angle (KFWDKMSN),0,0x8117f2
Afterstart enrich (FNSA_0_A),0,0x8144da
Table:Hot start enrichment factor (KFHSTT),0,0x818bb2
Delta timing during warmup,0,0x816018
Max_indicated_torque_check,0,0x81f242
Max_indicated_torque_check,0,0x81f242
Max_indicated_engine_torque_MDIMX,0,0x815764
MAP_sensor_gradient,0,0x8116d4
MAP_sensor_offset,0,0x8116d6
Conversion_constant_from_MAF_to_relative_charge_KUMSRL,0,0x814fc4
MAF_offset_MLOFS,0,0x811176
Normalized_fuel_consumption_per_cylinder_for_DIS_KVNPZ,0,0x8143ff
Min_RPM_for_misfire_recognition_fade_out_DMDDLU,0,0x814694
Min_RPM_for_acc_pedal_value_lockout_on_brake_operation_NWPMBBR,0,0x814c2d
pedal_lockout_on_brakes_activation_speed_VWPMBBR,0,0x814c46
Delay_time_for_acc_pedal_value_lockout_on_brake_operation_TWPMBBR,0,0x814c37
Pedal_volts_for_full_throttle_UPWGVG,0,0x814c45
Speed_before_rpm_limit_raised,0,0x815773
Water_temp_before_rpm_limit_raised_TMOTNMX,0,0x812f9c
Max_duration_of_raised_rpm_limit_TNMXH,0,0x812fa0
Main_RPM_Limit_NMAX,0,0x812f92
Time_under_rpm_limit_before_activating_raised_rpm_limit_ITNMXH,0,0x812f90
Max_rate_rpm_change_DNMAX,0,0x812f88
Max_RPM_with_doubled_ignition_detected_NMAXDZ,0,0x812f94
delta_for_rpm_limit_for_double_ignition_DNMAXDZ,0,0x812f8a
Max_rpm_on_doubled_ignition_detection_NMAXDZ,0,0x812f94
Max_rpm_on_safety_fuel_cutoff_SKA_NMXDKPU,0,0x812f9a
Max_rpm_on_rpm_gauge_fail_NMAXNL,0,0x812f96
rpm_deviation_above_limit_for_all_cyl_cut_DNMAXH,0,0x812f8c
Dwell_time_in_NMAX_before_change_over_in_calibration_TNMAXP,0,0x812f9e
Duration_for_active_alternative_calibration_of_maximum_rpm_ITNMAXP,0,0x812f8e
Raised_rpm_limit_NMAXOG,0,0x81f4f2
Codeword_No_ROM_check_reset_CW_NOROMCHKRESET,0,0x815c03
Min_rpm_for_misfire_recognition_fade_out_NMIALU,0,0x814697
Load_threshold_for_surge_recognition_for_misfire_recognition_attenuation_during_idle_RLSALULL,0,0x814699
Min_idle_air_mass_adaption_for_exhaust_gas_MSALLMN,0,0x814fc7
CW_Lambda_coordination_during_cat_warmup_CWLAMKH,0,0x8150ab
Speed_before_AC_control_active_VKO,0,0x81616e
engine_temp_from_cluster_for_AC_cutoff_TKOMBKOA,0,0x816156
engine_temp_from_cluster_for_AC_activation_TKOMBKOE,0,0x816157
temp_limit_before_AC_cutoff_TMKOAO,0,0x816169
temp_limit_before_AC_activated_TMKOAU,0,0x81616a
RPM_exceeded_threshold_for_cut_NMAXF,0,0x810ae8
Temp_during_start_for_requirements_adaption_TMSTMAD,0,0x81616b
max_speed_before_AC_cutoff_VKOAO,0,0x81616f
IAT_threshold_for_AC_cutoff_TANSKOB,0,0x816124
Speed_threshhold_for_AC_control_during_acceleration_VKOB,0,0x816170
SLOGIN,0,0x812122
GRAONLOGIN,0,0x81211e
ADRLOGIN,0,0x81211a
GRAOFLOGIN,0,0x81211c
Default coding for varient coding,0,0x812124
Dwell_time_for_dynamic_BPV_N249_control_THLDUVD,0,0x8121b0
Down_control_time_constant_for_fmvp_w_factor_TDPDK,0,0x8123f2
Ramp_slope_during_devation_regulation_of_ASR_torque_RAMPASR,0,0x8101c2
Min_voltage_for_diagnosis_MAP_sensor_limp_UADPLMN,0,0x8187c4
Max_voltage_for_diagnosis_MAP_sensor_limp_UADPLMX,0,0x8187c5
Min_voltage_for_diagnosis_MAP_sensor_UADPUMN,0,0x8187c6
Max_voltage_for_diagnosis_MAP_sensor_UADPUMX,0,0x8187c7
Debounce_time_for_end_of_cat_heater_cycles_per_min_during_idle_TKHLLAB,0,0x819240
Knock_regulation_Load_hysteresis_KRALH,0,0x8194b3
Knock_regulation_RPM_hysteresis_KRANH,0,0x8194b8
Control_deviation_threshold_for_LDR_positive_deviation_diagnosis_EDLDRP,0,0x819780
Regulation_deviation_threshold_for_starting_LDR_overboost_active_timer_ELDOB,0,0x819780
Lower_regulation_deviation_threshold_for_negative_adjustment_LDEIAU,0,0x81961a
Upper_regulation_deviation_threshold_for_negative_adjustment_LDEIAO,0,0x819617
Regulation_deviation_threshold_for_positive_adaption_I_Regulation_LDEIAP,0,0x819618
Regulation_deviation_threshold_for_rapid_positive_set_point_tracing_LDEIAPS,0,0x819619
Hysteresis_for_LDR_I_Adaption_curve_LDHIA,0,0x81961b
Changeover_deviation_threshold_for_dynamic_LDR_UMDYLDR,0,0x819637
Minimum_charge_LDR_for_DIA_LDR_maximum_permitted_pressure_SDLDRL,0,0x81982a
Time_threshold_for_Dia_LDR_control_deviation_TDLDRA,0,0x81982b
Time_threshold_for_Dia_LDR_control_deviation_B_mxldra_TDLDRA2,0,0x81982c
Delay_time_for_Dia_LDR_control_deviation_detection_cycle_flag_TLDRA,0,0x81982d
Overboost_cutoff_delay_step_1_TULV1,0,0x81982e
Delay_time_for_overboost_failure_recovery_TULV3,0,0x81982f
Constant_for_fuel_consumption_display_KVB,0,0x81a348
Max_air_mass_b4_shutoff_secondary_air_injection_MLSLMX,0,0x81a4de
min_airmass_for_diagnosis_MLWDSLMN,0,0x81a548
Airmass_threshold_for_dynamic_testing_behind_cat_MLLASH,0,0x81b392
Delta_pressure_value_for_signal_comparison_of_pressure_sensor_with_ambient_pressure_DPDSVLU,0,0x81bba4
max_airflow_for_load_calculation_MLMAX_SAE_J1979,0,0x81bc10
EGT_threshold_for_component_protection_TABGBTS,0,0x81c14a
target_EGT_B1_TABGSS,0,0x81c1ac
target_EGT_B2_TABGSS2,0,0x81c1ae
EGT_sensor_error_limit_TDATSO,0,0x81bffe
DTC_CONFIG_BITS1,0,0x818d96
EGT_threshold1_950,0,0x81bffc
EGT_threshold2_940,0,0x81bff8
EGT_threshold3_1035,0,0x81bffa
Tank_ventilation_time_for_basic_adaption_TTEGA,0,0x81c386
Supplemental_codeword__short_strip_reqs_display_group_195_CWFA195A,0,0x81ca56
LDR_control_param_Q0_in_stationary_operation_LDRQ0S,0,0x81d5c6
Upper_duty_cycle_limit_for_LDR_TVLDMX,0,0x81d61e
Conversion_of_relative_fuel_mass_rk_to_effective_injector_time_te_KRKTE,0,0x818da8
EGT_SENSOR_CHECK,0,0x8592e6(pc)
Engine Temp From Cluster,0,0x380bb8
Engine Load,0,0xf989