Pages: [1]
Author Topic: bosch 0281006059 for 5120 hack  (Read 1603 times)
tao13
Full Member
***

Karma: +0/-12
Offline Offline

Posts: 215


« on: May 17, 2020, 12:52:19 PM »

Hi everyone.
Please tell me if somebody used this bosch 0281006059 for 5120 hack?
I found it as 4mbar sensor!
What sensor do you recomand for 5120hack? 4 or 5 bar?
Thanks in advance
Logged
fukenbroken
Hero Member
*****

Karma: +116/-8
Offline Offline

Posts: 981


mk4 1.8T AUM


« Reply #1 on: May 17, 2020, 01:09:48 PM »

If you're planning to boost up to 4bar then a 5 bar sensor is your choice for sure
Logged
tao13
Full Member
***

Karma: +0/-12
Offline Offline

Posts: 215


« Reply #2 on: May 17, 2020, 11:24:41 PM »

thanks, i want to work maximum 2-2.1bar.
i asked for sensor type because i saw different opinion and different problem with theier calibration in 5120 hack strategy
i wan to use one who was tested and confirmed.
thanks in advance
Logged
dilly
Sr. Member
****

Karma: +12/-36
Offline Offline

Posts: 304



« Reply #3 on: June 28, 2020, 11:07:57 AM »

thanks, i want to work maximum 2-2.1bar.
i asked for sensor type because i saw different opinion and different problem with theier calibration in 5120 hack strategy
i wan to use one who was tested and confirmed.
thanks in advance
i would go 4 bar since you are planning on going past 2 bar you have to account for atmospheric pressure. so if you plan on boosting 2.1 bar + 1 bar atmosphere, a 4 bar would be safe bet since you would max out a 3 bar
Logged
jdm
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 5


« Reply #4 on: June 28, 2020, 07:49:33 PM »

No issues using 0 281 006 059, just be aware on 2.7T you will require a spacer for the throttle boot as the outer diameter of the probe oring is about half that of the stock unit. 

Your local hardware store should have something you can make work. Hint, check the plumbing section - I found a (nearly) plug and play brass fitting for under a dollar.

DSLGRAD / DSLOFS are 437.5 / 31.25 for this sensor.
Logged
tao13
Full Member
***

Karma: +0/-12
Offline Offline

Posts: 215


« Reply #5 on: August 31, 2020, 08:57:01 AM »

thanks a lot to all.
i decided for 4bar sensor like i wrote upstairs because i found bosch oem at a very good price in my country.
i have my stock 2.5bar bosch sensor for my aum engine with small diameter and this new one is the same , is for small hole diamter,
thanks jdm for your advices regards DSLGRAD / DSLOFS
please tell me, for the rest 5120 hack procedure ( is saw the list from wiki) i must divide with 2 some maps and ither multiply with 2 , correct?
i think the nyet and british made theier examples for 5bar sensor.
the hardest jos will be the asm code who must implement it too?
thanks in advance
Logged
K92
Full Member
***

Karma: +0/-1
Online Online

Posts: 108


« Reply #6 on: August 31, 2020, 11:11:18 AM »

thanks a lot to all.
i decided for 4bar sensor like i wrote upstairs because i found bosch oem at a very good price in my country.
i have my stock 2.5bar bosch sensor for my aum engine with small diameter and this new one is the same , is for small hole diamter,
thanks jdm for your advices regards DSLGRAD / DSLOFS
please tell me, for the rest 5120 hack procedure ( is saw the list from wiki) i must divide with 2 some maps and ither multiply with 2 , correct?
i think the nyet and british made theier examples for 5bar sensor.
the hardest jos will be the asm code who must implement it too?
thanks in advance

When you do the hack , you can use sensor up to 5bar. Procedure for the hack is same whatever sensor you use. Only difference is DSLGRAD / DSLOFS .
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.017 seconds with 17 queries. (Pretty URLs adds 0s, 0q)