horon6155
Jr. Member
Karma: +0/-4
 Offline
Posts: 41
|
 |
« on: May 24, 2020, 10:39:28 AM »
|
|
|
hi Guys,
my control unit hanged again. I suspect water damage.
now I have to buy a new one. I have a good offer for a passat 3b 1.8t me7.5 with the part number: 4B0906018DH and bosch number: 0261207928 to get. I would also love to strike, but would it work at all? could I transfer a golf 4 / audi a3 me7.5 dump to this control unit and it would work or are they very different control units?
I have everything for the rest of the conversion from m3.8.3 to me7.5. only I have not found a golf 4 / audi a3 control unit which is comparatively good and cheap.
|
|
|
|
|
Logged
|
|
|
|
fknbrkn
Hero Member
Karma: +186/-24
Offline
Posts: 1455
mk4 1.8T AUM
|
|
« Reply #1 on: May 24, 2020, 01:28:34 PM »
|
|
|
Iirc this one with different bootrom
Also they're not water proof
|
|
|
|
|
Logged
|
|
|
|
horon6155
Jr. Member
Karma: +0/-4
Offline
Posts: 41
|
|
« Reply #2 on: May 24, 2020, 11:25:59 PM »
|
|
|
so it wouldn't work or would it work?
|
|
|
|
|
Logged
|
|
|
|
|
BlackT
|
|
« Reply #3 on: May 25, 2020, 01:44:51 AM »
|
|
|
What is passat ECU number and software version?
|
|
|
|
|
Logged
|
|
|
|
horon6155
Jr. Member
Karma: +0/-4
Offline
Posts: 41
|
|
« Reply #4 on: May 25, 2020, 02:29:02 AM »
|
|
|
Passat Ecu-number:4B0906018DH and Bosch-Number: 0261207928
|
|
|
|
|
Logged
|
|
|
|
|
BlackT
|
|
« Reply #5 on: May 25, 2020, 02:34:49 AM »
|
|
|
Passat Ecu-number:4B0906018DH and Bosch-Number: 0261207928
DH have 6.02 boot version. Most of A3 golf have 5.12. Soo it can't work |
|
|
|
|
Logged
|
|
|
|
horon6155
Jr. Member
Karma: +0/-4
Offline
Posts: 41
|
|
« Reply #6 on: May 25, 2020, 02:59:42 AM »
|
|
|
aaa understand. and there is no way to change the boot version? is there a me7.5 from the audi a4 or passat that has the same boot version? As far as I know, the pin assignments are the same as for the A3.
|
|
|
|
|
Logged
|
|
|
|
|
prj
|
|
« Reply #7 on: May 25, 2020, 05:23:05 AM »
|
|
|
aaa understand. and there is no way to change the boot version? is there a me7.5 from the audi a4 or passat that has the same boot version? As far as I know, the pin assignments are the same as for the A3.
Dude the bootrom is OTP. Yes there is a way to change it - replace the main processor with a new one! For all intents and purposes NO. Also, on transverse engine platform you NEED to get a waterproof sealed ECU, because it gets rain on it. A 4B will never ever work, because it's not protected in any way, it won't fit the bracket and it is designed to be housed in a weatherproof box. |
|
|
|
|
Logged
|
|
|
|
horon6155
Jr. Member
Karma: +0/-4
Offline
Posts: 41
|
|
« Reply #8 on: May 25, 2020, 10:12:18 AM »
|
|
|
the control unit should enter a golf 3. Since I already have water damage, I decided to pack the control unit inside. therefore, this shouldn't cause any problems. The only thing according to your generous information would be the bootrom. if I can do that simply by swapping the main processor, it wouldn't be such a big problem.
such main processors do not cost the world now or do they?
|
|
|
|
|
Logged
|
|
|
|
fknbrkn
Hero Member
Karma: +186/-24
Offline
Posts: 1455
mk4 1.8T AUM
|
|
« Reply #9 on: May 25, 2020, 11:19:43 AM »
|
|
|
It was the sarcasm
Go get transverse ecu
|
|
|
|
|
Logged
|
|
|
|
Stoti
Full Member
Karma: +0/-0
Offline
Posts: 79
|
|
« Reply #10 on: May 25, 2020, 03:57:16 PM »
|
|
|
Currenty i tested last week CG passat ecu crossflashed from 2.0 N/A ALT on AMK engine cuz it was with ABT tune wokrs great , but they differ hardware one is not water resist (without sealant on edges) and it uses diferent case it will be hard to fit. DH will not work i think it uses newer processor if im not wrong.
|
|
|
|
|
Logged
|
|
|
|
|
Blazius
|
|
« Reply #11 on: May 26, 2020, 11:34:04 AM »
|
|
|
Currenty i tested last week CG passat ecu crossflashed from 2.0 N/A ALT on AMK engine cuz it was with ABT tune wokrs great , but they differ hardware one is not water resist (without sealant on edges) and it uses diferent case it will be hard to fit. DH will not work i think it uses newer processor if im not wrong.
Wait what , you flashed a NA tuned file on 1.8T me7.5 hardware? Did I understand that right lolz |
|
|
|
« Last Edit: May 26, 2020, 11:44:25 AM by Blazius »
|
Logged
|
|
|
|
cessnas
Full Member
Karma: +2/-17
Offline
Posts: 77
|
|
« Reply #12 on: May 26, 2020, 11:41:06 AM »
|
|
|
As long as they have the same bootloader you can cross flash.
You should also move over the eeprom dump.
You can find the bootloader version with me7check.
I put an ECU from an A4 in my Golf, just added some black silicone around the edges to seal it. Works with no issues so far
|
|
|
|
|
Logged
|
|
|
|
|
prj
|
|
« Reply #13 on: May 26, 2020, 12:02:29 PM »
|
|
|
the control unit should enter a golf 3. Since I already have water damage, I decided to pack the control unit inside. therefore, this shouldn't cause any problems. The only thing according to your generous information would be the bootrom. if I can do that simply by swapping the main processor, it wouldn't be such a big problem.
such main processors do not cost the world now or do they?
Replacing and programming a such processor is strong three digits labor, the processors are probably discontinued. If not, the chip will cost more than an ECU. What's your obsession with this? A proper ECU is like 25-40€ on eBay. |
|
|
|
|
Logged
|
|
|
|
Stoti
Full Member
Karma: +0/-0
Offline
Posts: 79
|
|
« Reply #14 on: May 26, 2020, 12:59:54 PM »
|
|
|
Wait what , you flashed a NA tuned file on 1.8T me7.5 hardware? Did I understand that right lolz
No i got the ecu from NA ALT i think 2.0l 5v auto and flashed it with 1.8t CG and it works perfect. Now its mounted on 1.8t leon With AMK engine because it was with ABT tune. |
|
|
|
|
Logged
|
|
|
|
|
