Chris070
Newbie
Karma: +0/-0
 Offline
Posts: 14
|
 |
« on: July 16, 2020, 08:09:22 AM »
|
|
|
Hello my friends,im new here and im from germany. Sorry about my not so perfect english  Im trying to read my ECU from a Passat W8. It is a ME7.1.1 ECU. I use Galletto from this Forum with an FTDI Cable. I desoldered the resistor from the backside of the ECU and grounded pin 24 permanent. I can read it with galletto but it cant get the ecu id. And i dont know if the dump i readed is correct.can somebody check it for me? And how i must read it correctly? Best regards and thank you |
|
|
|
|
Logged
|
|
|
|
|
gremlin
|
|
« Reply #1 on: July 16, 2020, 10:36:24 AM »
|
|
|
I can read it with galletto but it cant get the ecu id. And i dont know if the dump i readed is correct.can somebody check it for me?
The file was read incorrectly. |
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #2 on: July 16, 2020, 01:07:17 PM »
|
|
|
I desoldered the resistor from the backside of the ECU and grounded pin 24 permanent.
That isn't how any of this works. |
|
|
|
|
Logged
|
|
|
|
|
|
Chris070
Newbie
Karma: +0/-0
Offline
Posts: 14
|
|
« Reply #4 on: July 17, 2020, 08:17:05 AM »
|
|
|
I read it again and this time i think its right. can somebody check it please?
|
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #5 on: July 17, 2020, 09:05:21 AM »
|
|
|
Which pin24? If on the the flash that definitely isn't good.
|
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #6 on: July 17, 2020, 09:06:00 AM »
|
|
|
I read it again and this time i think its right. can somebody check it please?
This looks better |
|
|
|
|
Logged
|
|
|
|
|
gremlin
|
|
« Reply #7 on: July 17, 2020, 01:14:21 PM »
|
|
|
I read it again and this time i think its right. can somebody check it please?
Now dump file it's OK. |
|
|
|
|
Logged
|
|
|
|
Chris070
Newbie
Karma: +0/-0
Offline
Posts: 14
|
|
« Reply #8 on: July 18, 2020, 09:27:44 AM »
|
|
|
Can somebody help me to find ESKONF in this dump? Im searching for hours and get nothing  |
|
|
|
|
Logged
|
|
|
|
|
Blazius
|
|
« Reply #9 on: July 18, 2020, 02:56:50 PM »
|
|
|
Can somebody help me to find ESKONF in this dump? Im searching for hours and get nothing ESKONF tool , ME7 Swiss knife tool not working? Should be around maf scale usually. |
|
|
|
|
Logged
|
|
|
|
Chris070
Newbie
Karma: +0/-0
Offline
Posts: 14
|
|
« Reply #10 on: July 19, 2020, 02:13:44 PM »
|
|
|
No it just finds a 7bit adress but i dont think eskonf has 7bits with an 8 cylinder engine
|
|
|
|
|
Logged
|
|
|
|
|
gremlin
|
|
« Reply #11 on: July 20, 2020, 01:00:18 PM »
|
|
|
Can somebody help me to find ESKONF in this dump? Im searching for hours and get nothing ESKONF -> $109B7, 1x13. 8-bit But keep in mind that the cell assignments are unique to this W8 engine and are very different from those for the V6. |
|
|
|
|
Logged
|
|
|
|
Chris070
Newbie
Karma: +0/-0
Offline
Posts: 14
|
|
« Reply #12 on: July 20, 2020, 09:34:38 PM »
|
|
|
Thank you  then i will try and error,informations for the w8 are very rare |
|
|
|
|
Logged
|
|
|
|
|
|
|
gremlin
|
|
« Reply #14 on: July 21, 2020, 11:48:05 AM »
|
|
|
then i will try and error,informations for the w8 are very rare One of possible ESKONF variants for ME7.1.1 WR8 ecu. |
|
|
|
|
Logged
|
|
|
|
|
