Pages: [1]
Author Topic: ME7 8D0907551D AGB need immo OFF  (Read 4993 times)
Jaamboo
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 5


« on: September 09, 2020, 11:49:43 AM »

Hey Guys.
i hope im right here.
I have a problem with my swaped s6 c5 with s4 b5 engine. Engine starts for 1 sec then turn off.
I think its the immo in the ecu.

Setup:
8D0907551D
Bosch 0261206382
Eeprom 950403

attached eeprom file in here i hope someone can help me turn immo off

Thanks guys have a nice one.
Logged
elektronik13
Full Member
***

Karma: +10/-32
Offline Offline

Posts: 198


« Reply #1 on: September 09, 2020, 12:29:12 PM »

Hey Guys.
i hope im right here.
I have a problem with my swaped s6 c5 with s4 b5 engine. Engine starts for 1 sec then turn off.
I think its the immo in the ecu.

Setup:
8D0907551D
Bosch 0261206382
Eeprom 950403

attached eeprom file in here i hope someone can help me turn immo off

Thanks guys have a nice one.

the eeprom read is corrupted
read again
Logged
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12232


WWW
« Reply #2 on: September 09, 2020, 01:25:32 PM »

Convert to M, better defined, no immo.
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
Jaamboo
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 5


« Reply #3 on: September 10, 2020, 10:23:27 AM »

the eeprom read is corrupted
read again

Hey every read of the file will look the same ...
i have a ch341a usb reader(software 1.29 with 25lc160 as selected chip) and reading direkt from ecu via clamps but every time the fin from ecu and immo is in XXX
could be a problem with a soldered chip from ABT Tuner ?

Hope someone can help me ..  Huh
Logged
Audiquattro44
Full Member
***

Karma: +18/-11
Offline Offline

Posts: 85


« Reply #4 on: September 10, 2020, 11:38:35 AM »

test it
Logged
Jaamboo
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 5


« Reply #5 on: September 11, 2020, 11:45:39 AM »

the eeprom read is corrupted
read again

Hey,
made some changes in my reading setup would be nice if u can take a look

 i hope someone can do something with this .. Huh
Logged
elektronik13
Full Member
***

Karma: +10/-32
Offline Offline

Posts: 198


« Reply #6 on: September 11, 2020, 04:04:23 PM »

Hey,
made some changes in my reading setup would be nice if u can take a look

 i hope someone can do something with this .. Huh

immo off
Logged
Blazius
Hero Member
*****

Karma: +89/-40
Offline Offline

Posts: 1277



« Reply #7 on: September 11, 2020, 04:58:28 PM »

Again, why dont you crossflash/conv to m box which is an US market file , that is very well defined and it has no WFS/immo.
Logged
Jaamboo
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 5


« Reply #8 on: September 12, 2020, 11:41:22 AM »

immo off

Thanks a lot worked perfectly  Grin

Again, why dont you crossflash/conv to m box which is an US market file , that is very well defined and it has no WFS/immo.
Sorry, but im not that deep into ecu stuff but im willing to learn about it . Can u tell me what do u mean with convert to m box ?  Roll Eyes
Logged
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12232


WWW
« Reply #9 on: September 12, 2020, 11:49:06 AM »

Can u tell me what do u mean with convert to m box ?  Roll Eyes

It means ditching this:
Quote
soldered chip from ABT Tuner

and doing your own tune
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
Jaamboo
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 5


« Reply #10 on: September 21, 2020, 12:15:46 PM »

It means ditching this:
and doing your own tune

Hey im interested in programming my own tune.
You say that i have to ditch the soldered chip ?
So i need a new chip that i solder in ?
Is there anything that i have to worry about for the chip ?
Or should i buy the same that is installed now ?
I heard that i can upgrade to an Engine code BES ecu ? Is there any differents between the hardware from the ecus or are there software changes ?
With my 551D ecu i cant read misfire counter or even misfire on which zylinder...

Sorry for the "dumb" questions but i want to get slowly into tuning and my current setup but here is soo much stuff to read but i think my head will blow up Shocked
if u have some interessting threads that i can read to understand this better give me a link  Roll Eyes
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.02 seconds with 16 queries. (Pretty URLs adds 0s, 0q)