Pages: [1] 2
Author Topic: mpps EDC17c10 and k-line!  (Read 8916 times)
beou
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 8


« on: September 12, 2020, 06:48:06 AM »

Hello!!
 Newbie here trying to flash my own citroen c3!
I have an EDC17c10, (lid opened and ready for boot mode)
When i am trying to ECU id or read, the mpps v18 prompts this:
'Please make sure that KLINE is connected to the ignition pin'
As i know, flashing an EDC17c10 with mpps does not require the k-line cable! Just CAN-H and CAN-L!
Do i have to use K line cable too?

Thanks!
Logged
xXxCryxXx
Full Member
***

Karma: +3/-17
Offline Offline

Posts: 156


« Reply #1 on: September 12, 2020, 06:54:22 AM »

Hello!!
 Newbie here trying to flash my own citroen c3!
I have an EDC17c10, (lid opened and ready for boot mode)
When i am trying to ECU id or read, the mpps v18 prompts this:
'Please make sure that KLINE is connected to the ignition pin'
As i know, flashing an EDC17c10 with mpps does not require the k-line cable! Just CAN-H and CAN-L!
Do i have to use K line cable too?

Thanks!
Clone?

X-Boost Performance

Logged
beou
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 8


« Reply #2 on: September 12, 2020, 07:06:23 AM »

Its a clone yes!!
Logged
xXxCryxXx
Full Member
***

Karma: +3/-17
Offline Offline

Posts: 156


« Reply #3 on: September 12, 2020, 07:08:19 AM »

Its a clone yes!!
Make a second green kabel on the main green kabel for ignition

X-Boost Performance

Logged
xXxCryxXx
Full Member
***

Karma: +3/-17
Offline Offline

Posts: 156


« Reply #4 on: September 12, 2020, 07:10:40 AM »

Make a second green kabel on the main green kabel for ignition

X-Boost Performance
and Picture of wiring please

X-Boost Performance

Logged
beou
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 8


« Reply #5 on: September 12, 2020, 07:19:32 AM »

Thanks for your reply!
EDC17c10 needs ground at pin 4,
12v at pin 2, and 12v too at pin 19!
Pin 19 is the ignition pin i assume!
CAN-H at pin 40 and CAN-L at pin 52!
In the mpps breakout cable, the CAN-H is the blue wire!
The CAN-L is the orange one!
K-line is green!
Why do i need two K-line cables?
In the photo, CAN-H and CAN-L are marked with different colours but i think that it doesnt matter!
Logged
xXxCryxXx
Full Member
***

Karma: +3/-17
Offline Offline

Posts: 156


« Reply #6 on: September 12, 2020, 07:21:24 AM »

Thanks for your reply!
EDC17c10 needs ground at pin 4,
12v at pin 2, and 12v too at pin 19!
Pin 19 is the ignition pin i assume!
CAN-H at pin 40 and CAN-L at pin 52!
In the mpps breakout cable, the CAN-H is the blue wire!
The CAN-L is the orange one!
K-line is green!
Why do i need two K-line cables?
In the photo, CAN-H and CAN-L are marked with different colours but i think that it doesnt matter!
Do you have connected pin 9 and 12?

X-Boost Performance

Logged
xXxCryxXx
Full Member
***

Karma: +3/-17
Offline Offline

Posts: 156


« Reply #7 on: September 12, 2020, 07:22:52 AM »

Sorry wrong text Where is the Pin Out of your seller for the mmps flasher?

X-Boost Performance

Logged
beou
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 8


« Reply #8 on: September 12, 2020, 07:35:41 AM »

Seller didnt provided any pinout!
I did a research and i think that the colors are correct!
I can confirm the the BLUE cable is CAN-H and ORANGE is CAN-L!
Used a multimeter and checked that the BLUE goes straight at pin 7 of the a1050c CAN transeiver chip!
So is the ORANGE connected straigth to pin 6 of the same chip.
Logged
xXxCryxXx
Full Member
***

Karma: +3/-17
Offline Offline

Posts: 156


« Reply #9 on: September 12, 2020, 07:37:07 AM »

Seller didnt provided any pinout!
I did a research and i think that the colors are correct!
I can confirm the the BLUE cable is CAN-H and ORANGE is CAN-L!
Used a multimeter and checked that the BLUE goes straight at pin 7 of the a1050c CAN transeiver chip!
So is the ORANGE connected straigth to pin 6 of the same chip.
Wait i will later look at my KTag the Pinout for Bootmode right? it sould be the same

X-Boost Performance

Logged
beou
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 8


« Reply #10 on: September 12, 2020, 07:42:19 AM »

Thanks in advance for your effort!
I think that Ktag has different colors!
Logged
xXxCryxXx
Full Member
***

Karma: +3/-17
Offline Offline

Posts: 156


« Reply #11 on: September 12, 2020, 09:46:04 AM »

Thanks in advance for your effort!
I think that Ktag has different colors!
no i dont Think so... you need Bootpin too....

X-Boost Performance

Logged
beou
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 8


« Reply #12 on: September 12, 2020, 10:07:43 AM »

Thanks again!! I have already soldered a boot pin wire from the begining!
But the result is the same!


 Undecided
Logged
xXxCryxXx
Full Member
***

Karma: +3/-17
Offline Offline

Posts: 156


« Reply #13 on: September 12, 2020, 10:18:55 AM »

Thanks again!! I have already soldered a boot pin wire from the begining!
But the result is the same!


 Undecided
Maybe the Protocol of Clone MPPS is wrong .... that happens becuse Clone sorry M8 ...
Logged
beou
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 8


« Reply #14 on: September 12, 2020, 10:27:04 AM »

OK! I will keep trying!

Thanks a lot for your help man!!

Cheers
Logged
Pages: [1] 2
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.02 seconds with 16 queries. (Pretty URLs adds 0s, 0q)