Hi everybody!
i've spent much time during the last weeks to perform a right (as possible i can) and rich of values XDF (starting from a BAM one) and now i would like share it with you, i think that will be useful for someone like me have an APX engine with the 8L0906018M_0002 ECU.
After that i've re-started again with tuning my ECU making a new .bin based on the original one.
That's how i've done until now:

Edit Log for 04_Audi TT.bin created by TunerPro.
**************************************************************************
12/11/2020 22:42:43  Scalar:    KRKTE changed from 0.74880 ms/% (0xEA) to 0.06080 ms/% (0x13).
12/11/2020 22:43:03  Scalar:    KRKTE changed from 0.06080 ms/% (0x13) to 0.06080 ms/% (0x13).
12/11/2020 22:43:09  Scalar:    KRKTE changed from 0.06080 ms/% (0x13) to 0.06080 ms/% (0x13).
12/11/2020 22:45:32  Table:     Axis: TVUB Voltage changed.
12/11/2020 22:55:53  Table:     TVUB changed.
12/11/2020 22:56:19  Table:     TVUB changed.
12/11/2020 22:56:33  Table:     TVUB changed.
12/11/2020 22:58:05  Scalar:    TEMIN changed from 0.0224 ms (0x0007) to 0.7488 ms (0x00EA).
12/11/2020 22:58:11  Scalar:    TEMIN changed from 0.7488 ms (0x00EA) to 0.7488 ms (0x00EA).
12/11/2020 23:01:47  Scalar:    TEMIN changed from 0.7488 ms (0x00EA) to 0.0224 ms (0x0007).
12/11/2020 23:03:05  Scalar:    TEMIN changed from 0.0608 ms (0x0013) to 0.7488 ms (0x00EA).
12/11/2020 23:16:24  Table:     NLLM changed.
12/11/2020 23:20:29  Table:     NFSM changed.
12/11/2020 23:33:48  Table:     KFFWL changed.
12/11/2020 23:34:19  Table:     KFFWL changed.
12/11/2020 23:40:57  Table:     LAMFA axis changed.
12/11/2020 23:41:16  Table:     LAMFA axis changed.
12/11/2020 23:41:26  Table:     LAMFA axis changed.
12/11/2020 23:41:38  Table:     LAMFA axis changed.
12/11/2020 23:46:29  Table:     LAMFA changed.
12/11/2020 23:47:45  Scalar:    TLAFA changed from 0.100 sec (0x01) to 0.000 sec (0x00).
12/12/2020 12:33:56  Table:     LDRXN changed.
12/12/2020 12:34:21  Table:     LDRXNZK changed.
12/12/2020 12:37:02  Table:     KFLDHBN changed.
12/12/2020 13:25:22  Table:     KFVPDKSD Axis changed.
12/14/2020 23:17:46  Table:     KFTARX changed.
12/15/2020 23:10:09  Scalar:    CWMDAPP changed from 1.00  (0x01) to 8.00  (0x08).
12/15/2020 23:19:06  Scalar:    TVLDMX changed from 95.0000 % (0x4A38) to 30.0000 % (0x1770).
**************************************************************************

i didn't changed any values or axis of the tables KFLDIMX / KFLDRL / KFLDRAPP because i'll do this in a second time as suggest in this usefull topic: http://nefariousmotorsports.com/forum/index.php?topic=517.msg4028#msg4028
Now, using the TVLDMX value i would find the "open loop point" to be sure to be always in open loop with my boost.

At this point i'm looking for tuning KFMIOP / KFMIRL / KFMIZUFIL / KFMIZUOF, i've understand that i've to correct the tables according to my new LDRXN values, and so, the new boost request (is a simplyfication, i know), but onestly i didn't understand how i can perform it. I've understand that i've to log mrfa/mimax/mifa/milsol/misopl1 but for the first time what i've to do for setting rightly that tables?.
i've understand that if i dont do this my car didn't runs righly and so i think i can't perform a usefull log for improve my tuning...i'm wrong???.
So please someone could explain me how can i set this tables? thank you so much.

The reason of the changes are showed below into the picture attached, on my engine as you can see, I’ve mounted the 550cc injectors.
I’d changed NNLM because my car are skat and with the SAE pump removed, so I preferred to set my idle to 900 rpm.
I changed KFWLL table because my engine, during warmup goes a bit lean (~17:1 of AFR).
I changed CWMDAPP like the S4 say and TVLDMX for reduce the WGDC for finding the right set point for going always in open loop and next being able to calibrate KFLDIMX and KFLDRL.

Ok, thanks for your evaluation.
The TEMIN value was given by a my friend that have the same injectors and works fine.
About the limiting the WGDC if you don’t like the way i used, tell your way to do. I’m sure that I’ll learn something....and what about the topic’s questions? Can you help me?

Ok Adam thank you! And what about IOP axis? I’ve to change the last row from 191 to 250?
Thank you

Your 04 log is corrupted. Please post original, unedited csvs

Also go WOT so ECUxPlot's filter works.


Finally, 05 looks horrible. I don't know where to start.

I'll perfome another log using the 04 map so... 

stop lifting during log.

Get a log with wot to redline.

Also why are you requesting boost near the map limit?

You need to stop getting distracted by the complicated stuff and fix the basics.