Pages: [1]
Author Topic: Can anyone spot any differences?  (Read 9521 times)
agentsmith988
Newbie
*

Karma: +4/-0
Offline Offline

Posts: 20


« on: September 24, 2010, 09:11:36 AM »

I'm pulling this from my thread over on AZ. I've been trying to figure out what tune I have (installed a boost gauge and ran some logs indicating about 15-17psi peaks...)

So I decided to try pulling the bin with the ECU Flasher and then to compare that bin to a stock file. I used Tunerpro to try and compare tables, but haven't been able to spot any differences. Can anyone point me in the right direction?

Extra info:
I've got a T-box
Read with the 29F800BT mem layout (not sure this was the correct one to use)
Compared to a stock M-Box file
AZ Thread http://www.audizine.com/forum/showthread.php/385731-Ran-Some-Logs...

Sorry everyone, I'm new to all of this...

http://www.mediafire.com/?eno6mojwlmhzq5y
« Last Edit: September 24, 2010, 09:13:18 AM by agentsmith988 » Logged
turboskipper
Jr. Member
**

Karma: +3/-0
Offline Offline

Posts: 40


« Reply #1 on: September 24, 2010, 11:41:46 AM »

I did a compare on a factory mbox file and found lots of changes. I don't have any maps defined in winols to easily spot things. I did however notice things like desired engine load are different which would certainly change boost pressure.
Logged
phila_dot
Hero Member
*****

Karma: +170/-11
Offline Offline

Posts: 1709


« Reply #2 on: September 24, 2010, 02:54:09 PM »

Use the difference tool to compare the stock bin against the one you pulled from your ECU.
Logged
agentsmith988
Newbie
*

Karma: +4/-0
Offline Offline

Posts: 20


« Reply #3 on: September 24, 2010, 03:09:11 PM »

Use the difference tool to compare the stock bin against the one you pulled from your ECU.

Ah, there they are! Now on to more reading to start figuring all this stuff out. Does this tune look familiar to anyone? I tried pulling it up in the Winols but it said it was "already modified" and wouldn't import the file (tuner right protection?).

Does this tune look like any of the shelf tunes available? Or am I dealing with something custom?
Logged
RaraK
Hero Member
*****

Karma: +58/-2
Offline Offline

Posts: 537


« Reply #4 on: September 26, 2010, 07:48:15 PM »

if i read that correctly you are comparing a T box to an M box?  That wont work, get a stock T box .bin to compare too, if you need help finding maps, look at the addresses in the .xdf file, and then look in that general area with a hex editor doing a comparison.
Logged
agentsmith988
Newbie
*

Karma: +4/-0
Offline Offline

Posts: 20


« Reply #5 on: September 27, 2010, 10:23:20 AM »

Yeah, I used a M Box file (I don't have a stock T-box file on hand, does anyone have one available for comparison?)

Would what turboskipper found in the engine load maps still distinguish a modified tune though? At this point, I really just want to know if I've got a stock map or not.
Logged
turboskipper
Jr. Member
**

Karma: +3/-0
Offline Offline

Posts: 40


« Reply #6 on: September 27, 2010, 11:52:10 AM »

Ya, my bad. I did not realize you had a tbox. So not sure if that lines up or not.
Logged
agentsmith988
Newbie
*

Karma: +4/-0
Offline Offline

Posts: 20


« Reply #7 on: September 28, 2010, 08:54:55 AM »

Is there anyone on here that can compare to a stock T-Box file for me? I really just want to know if I've got a stock flash or not...
Logged
Tony@NefMoto
Administrator
Hero Member
*****

Karma: +130/-4
Offline Offline

Posts: 1389


2001.5 Audi S4 Stage 3


« Reply #8 on: September 28, 2010, 02:51:53 PM »

Link to stock T box:
http://www.nefariousmotorsports.com/forum/index.php?topic=10.0
Logged

Remember you have to log in if you want to see the file attachments!
Info or questions, please add to the wiki: http://www.nefariousmotorsports.com/wiki
Follow NefMoto developments on Twitter: http://twitter.com/nefmoto
agentsmith988
Newbie
*

Karma: +4/-0
Offline Offline

Posts: 20


« Reply #9 on: September 28, 2010, 05:13:17 PM »

Alright, ran the difference tool on the t-box file you linked to with the bin I pulled from my ECU and Tunerpro just stalled. Push search, no results come up, but then try to click anything and the program stops responding. I'm guessing this is just a software glitch when comparing two identical bins? Anyone have any insight?
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.034 seconds with 16 queries. (Pretty URLs adds 0.001s, 0q)