Pages: 1 [2]
Author Topic: C6/B7 6HP19A gearbox to C5 5HP19 swap  (Read 41337 times)
EAF1-KR
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 19


« Reply #15 on: September 22, 2021, 05:48:31 PM »

DTC P1855 P0614  C6 3.2Gearbox 09L927156A 4F2910156D How to solve thanks
Logged
EAF1-KR
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 19


« Reply #16 on: September 22, 2021, 06:04:53 PM »

What DTC do you have?

DTC P1855 P0614 C6 3.2Gearbox 09L927156A 4F2910156D How to solve thanks
Logged
BlackT
Hero Member
*****

Karma: +79/-40
Offline Offline

Posts: 1426



« Reply #17 on: September 22, 2021, 11:49:34 PM »

Post VCDS screenshot
Logged
EAF1-KR
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 19


« Reply #18 on: September 23, 2021, 09:23:53 PM »

« Last Edit: September 23, 2021, 09:27:47 PM by EAF1-KR » Logged
EAF1-KR
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 19


« Reply #19 on: September 23, 2021, 09:30:07 PM »

Post VCDS screenshot
These DTC
Logged
Stoti
Full Member
***

Karma: +0/-0
Offline Offline

Posts: 79


« Reply #20 on: December 31, 2021, 10:00:32 AM »

Is there any info about reading and writing these geadrbox control unit  i found only flex , byteashooter but investing 3k for experiment is too much for me . 3.0 Mpi flash on 3.2fsi gearbox is possible and me7.1.1 controls it over 15K Km. But will be same commands messages and etc between med9 me7.1.1 and simos i want to try crossflash to 2.0tfsi
Logged
EAF1-KR
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 19


« Reply #21 on: April 19, 2022, 05:29:29 PM »

Is there any info about reading and writing these geadrbox control unit  i found only flex , byteashooter but investing 3k for experiment is too much for me . 3.0 Mpi flash on 3.2fsi gearbox is possible and me7.1.1 controls it over 15K Km. But will be same commands messages and etc between med9 me7.1.1 and simos i want to try crossflash to 2.0tfsi
Your M7 1.1 can it be directly matched with 6hp19? Don't you need to modify the TCU program?
Logged
EAF1-KR
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 19


« Reply #22 on: April 21, 2022, 12:27:27 AM »

here is connected box HYH from a4b7 2.0tfsi BWE
the throttle box detect, the opening percentages are displayed, the can bus is compatible, but it need to change the identifiers to 2tfsi in ecu flash
CANVERS, FMOTC

Hello, me7 5 1.8T engine, can you help solve some problems by changing to 6hp19
Logged
andreisrn
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 1


« Reply #23 on: June 14, 2024, 01:30:40 AM »

Hello, me7 5 1.8T engine, can you help solve some problems by changing to 6hp19

Hello,

Did you succeed to solve the problem with 1.8t ME7.5 and 6hp19 transmission ?
I am about to make a transmission conversion for B6 1.8T from Multitronic to 6hp19,and want to know for sure if is achievable.
Thank you!
Regards,
Andrei
Logged
Spen Holder
Jr. Member
**

Karma: +2/-6
Offline Offline

Posts: 33


« Reply #24 on: June 14, 2024, 07:55:51 AM »

Hello,

Did you succeed to solve the problem with 1.8t ME7.5 and 6hp19 transmission ?
I am about to make a transmission conversion for B6 1.8T from Multitronic to 6hp19,and want to know for sure if is achievable.
Thank you!
Regards,
Andrei
Message nameless, he did the 6hp mod for me. The only difference is I have a 2.7t.
Logged
Pages: 1 [2]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.019 seconds with 16 queries. (Pretty URLs adds 0s, 0q)