Rick81
Full Member
Karma: +0/-11
 Offline
Posts: 92
|
 |
« on: May 19, 2021, 11:51:13 PM »
|
|
|
Hi all ive got a 2000 Audi A6 4.2 V8 Ive deleted the Secondary air pump system off the car. I was wondering if anyone could help at all with removing the software for the secondary air system out of the Ecu please. Im happy to make a donation to the forum .
Im waiting on my cable to arrive its the ft232rl is that correct ?
|
|
|
|
|
Logged
|
|
|
|
|
Sandstorm3k
|
|
« Reply #1 on: May 20, 2021, 12:35:51 AM »
|
|
|
|
|
|
|
|
Logged
|
|
|
|
Rick81
Full Member
Karma: +0/-11
Offline
Posts: 92
|
|
« Reply #2 on: May 20, 2021, 01:05:59 AM »
|
|
|
Thankyou for your help i may have more questions soon. Im used to flashing Subarus and Evos not seen boot mode before this is all new to me. |
|
|
|
|
Logged
|
|
|
|
|
bamofo
|
|
« Reply #3 on: May 20, 2021, 11:58:23 AM »
|
|
|
Hi all ive got a 2000 Audi A6 4.2 V8 Ive deleted the Secondary air pump system off the car. I was wondering if anyone could help at all with removing the software for the secondary air system out of the Ecu please. Im happy to make a donation to the forum .
Im waiting on my cable to arrive its the ft232rl is that correct ?
I can help. once you get the Cable to read/write to your ECU either PM me or post the file here. |
|
|
|
|
Logged
|
|
|
|
Rick81
Full Member
Karma: +0/-11
Offline
Posts: 92
|
|
« Reply #4 on: May 22, 2021, 08:00:27 PM »
|
|
|
I can help. once you get the Cable to read/write to your ECU either PM me or post the file here.
Thankyou . |
|
|
|
|
Logged
|
|
|
|
Rick81
Full Member
Karma: +0/-11
Offline
Posts: 92
|
|
« Reply #5 on: May 22, 2021, 08:19:50 PM »
|
|
|
What drivers do i need to install to use for the ft232rl cable. Ive just download nefmoto just waiting on the cable.
|
|
|
|
|
Logged
|
|
|
|
|
macxxx
|
|
« Reply #6 on: May 22, 2021, 10:55:52 PM »
|
|
|
Ftdi webside
|
|
|
|
|
Logged
|
|
|
|
Rick81
Full Member
Karma: +0/-11
Offline
Posts: 92
|
|
« Reply #7 on: May 23, 2021, 11:46:17 PM »
|
|
|
I've opened the kkk vag-com to confirm the chip is right  Sent from my CPH1931 using Tapatalk |
|
|
|
|
Logged
|
|
|
|
Rick81
Full Member
Karma: +0/-11
Offline
Posts: 92
|
|
« Reply #8 on: May 24, 2021, 12:55:41 AM »
|
|
|
Ive tried the cable and it works. it connected at a baud rate of 108400 i think it was in dumb mode.
From here how do i extract the imformation from the ecu and save it to the computer?
|
|
|
|
|
Logged
|
|
|
|
Rick81
Full Member
Karma: +0/-11
Offline
Posts: 92
|
|
« Reply #9 on: May 24, 2021, 02:09:05 AM »
|
|
|
Also how long does it take to read the info from the ecu. Does it depend on the baud rate?
Sent from my CPH1931 using Tapatalk
|
|
|
|
|
Logged
|
|
|
|
|
bamofo
|
|
« Reply #10 on: May 24, 2021, 06:58:48 AM »
|
|
|
Ive tried the cable and it works. it connected at a baud rate of 108400 i think it was in dumb mode.
From here how do i extract the imformation from the ecu and save it to the computer?
I typically you the 52k baud rate on these. read takes about 2-3 minutes write takes about the same. |
|
|
|
|
Logged
|
|
|
|
|
|
Rick81
Full Member
Karma: +0/-11
Offline
Posts: 92
|
|
« Reply #12 on: May 24, 2021, 10:27:03 PM »
|
|
|
Read the car where do I go from here to make changes  Sent from my CPH1931 using Tapatalk |
|
|
|
|
Logged
|
|
|
|
|
RBPE
|
|
« Reply #13 on: May 25, 2021, 03:11:34 AM »
|
|
|
Load your saved bin in any hex editor - HXD & Tunerpro are what most use, winols demo may make it easier to read without being able to build maps/change data. HXD to just change hex data, Tunerpro to build maps/a def file too.
EDIT - Then start by looking for ESKONF as detailed in the links, you'll prob need a def file/help/post your bin up for the other bits
|
|
|
|
« Last Edit: May 25, 2021, 03:19:26 AM by RBPE »
|
Logged
|
|
|
|
Rick81
Full Member
Karma: +0/-11
Offline
Posts: 92
|
|
« Reply #14 on: May 25, 2021, 03:13:54 AM »
|
|
|
Load your saved bin in any hex editor - HXD & Tunerpro are what most used, winols demo may make it easier to read without being able to build maps/change data. HXD to just change hex data, Tunerpro to build maps/a def file too.
Hi it's saved as a xml file is that still good to use. I only want to switch off my secondary air pump thing Sent from my CPH1931 using Tapatalk |
|
|
|
|
Logged
|
|
|
|
|
