Pages: [1]
Author Topic: 1.8t multimap here  (Read 9165 times)
fukenbroken
Hero Member
*****

Karma: +153/-12
Online Online

Posts: 1212


mk4 1.8T AUM


« on: July 24, 2021, 07:47:02 AM »

Just my 2c back to nefmoto
This is multimap routine ive made 7yrs ago for ldrxn / zk and kfzw/2 switching with clutch and cruise stalk
Indicates with tacho needle
So you should hold the clutch and then tap set btn. On first tap it shows current selected map on tacho and after 1s returns to nmot if not pressed again. If pressed again it loops through maps_qt on every tap
Could be switched anytime even on wot  Shocked
Not used eeprom so returns to 1st set when ecu lost power

Xdf included
Maps_qt: num of sets in range of 1-4
Stock ldrxn/kfzw maps ignored

Bugs: clutch indicates warning of low oil pressure when engine is off or idling (on some engines) and tacho shows selected map with 2000+ rpm due to no oild pressure Smiley

Do not blindly flash included file. Its not checksummed and ldrxn / kfzw values are definetely not for a stock engine. Only for education purpose
Good luck!
Logged
1ktch
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 6


« Reply #1 on: July 26, 2021, 11:11:38 AM »

Hello
I wanted to check your files, but i've got xdf error, fgt2 dll missing, windows vista and above detected, and tunerpro just crashes. Is there a way to open your xdf?
Thx in adv
Logged
rogerius
Full Member
***

Karma: +51/-6
Offline Offline

Posts: 100


« Reply #2 on: July 27, 2021, 04:37:47 AM »

Thanks for sharing, it is very educational, shows how same things can be achieved differently. Applaud!
Logged
Sandstorm3k
Sr. Member
****

Karma: +10/-11
Offline Offline

Posts: 392



« Reply #3 on: July 30, 2021, 10:26:56 AM »

Cool stuff, thanks for sharing!
Logged
bamofo
Sr. Member
****

Karma: +34/-2
Offline Offline

Posts: 411


« Reply #4 on: August 03, 2021, 10:46:56 AM »

Just my 2c back to nefmoto
This is multimap routine ive made 7yrs ago for ldrxn / zk and kfzw/2 switching with clutch and cruise stalk
Indicates with tacho needle
So you should hold the clutch and then tap set btn. On first tap it shows current selected map on tacho and after 1s returns to nmot if not pressed again. If pressed again it loops through maps_qt on every tap
Could be switched anytime even on wot  Shocked
Not used eeprom so returns to 1st set when ecu lost power

Xdf included
Maps_qt: num of sets in range of 1-4
Stock ldrxn/kfzw maps ignored

Bugs: clutch indicates warning of low oil pressure when engine is off or idling (on some engines) and tacho shows selected map with 2000+ rpm due to no oild pressure Smiley

Do not blindly flash included file. Its not checksummed and ldrxn / kfzw values are definetely not for a stock engine. Only for education purpose
Good luck!

Thanks for sharing your work. I dont work on this platform but am always interested in learning more about how to do these things.
Logged
totti
Full Member
***

Karma: +15/-26
Offline Offline

Posts: 227


« Reply #5 on: September 10, 2021, 10:31:38 AM »

Just my 2c back to nefmoto
This is multimap routine ive made 7yrs ago for ldrxn / zk and kfzw/2 switching with clutch and cruise stalk
Indicates with tacho needle
So you should hold the clutch and then tap set btn. On first tap it shows current selected map on tacho and after 1s returns to nmot if not pressed again. If pressed again it loops through maps_qt on every tap
Could be switched anytime even on wot  Shocked
Not used eeprom so returns to 1st set when ecu lost power

Xdf included
Maps_qt: num of sets in range of 1-4
Stock ldrxn/kfzw maps ignored

Bugs: clutch indicates warning of low oil pressure when engine is off or idling (on some engines) and tacho shows selected map with 2000+ rpm due to no oild pressure Smiley

Do not blindly flash included file. Its not checksummed and ldrxn / kfzw values are definetely not for a stock engine. Only for education purpose
Good luck!

Thanks for sharing it. Can you tell how does it work? I could see functions at 8B4D00 8B4000 8B4700. Maps are stored from 8B5000.  8B4D00 seems to show the current map on odo with changing nmot. I could not find how to change map from 8B5000 to the ram.

Thank you
Logged
SAMI974
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 1


« Reply #6 on: June 03, 2022, 02:14:58 AM »

thank you  Wink
Logged
LoursRose
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 16


« Reply #7 on: September 20, 2022, 08:47:38 AM »

is it possible to integrate KRKTE?
Logged
prj
Hero Member
*****

Karma: +523/-155
Offline Offline

Posts: 4742


« Reply #8 on: September 20, 2022, 09:05:58 AM »

is it possible to integrate KRKTE?
Of course it is.
It's even possible to make ME7 control coffee machine.

Is it possible for you? Probably not if you need to ask.
Logged

PM's will not be answered, so don't even try.
fukenbroken
Hero Member
*****

Karma: +153/-12
Online Online

Posts: 1212


mk4 1.8T AUM


« Reply #9 on: September 24, 2022, 02:41:15 AM »

Krkte and kftsrl was implemented aswell for mr LoursRose

For those who want some modifications of the code - ask me in pm. DSG multimap based on selected dsg mode also completed. Pm for details. Not a free service.
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.021 seconds with 18 queries. (Pretty URLs adds 0s, 0q)