NefMoto > Technical > Cluster and Immobilizer (Moderator: ddillenger) > Help understanding CAN wake up to Audi A3 cluster
Pages: [1]
« previous next »
Author Topic: Help understanding CAN wake up to Audi A3 cluster  (Read 4756 times)
JakeGT
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 21
« on: October 17, 2021, 11:18:04 AM »
Hi,

I've been attempted to get an A3 cluster powered up on the bench (8P0920981F) but I'm struggling to get my head around the wiring. I have a CANanylst-ii CAN to USB tool but I don't understand how it's meant to be wired.

On the dash you have CAN H & L on pins 29 & 30 which I assumed went to the CANusb but CAN wakeup line is on pin 5 of the dash which I guess is where the signal needs to be sent but not sure how to wire it?



Thanks
Logged
macxxx
Sr. Member
****

Karma: +30/-1
Offline Offline

Posts: 498
« Reply #1 on: October 17, 2021, 01:40:16 PM »
send it just on CAN H & CANL
Logged
JakeGT
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 21
« Reply #2 on: October 18, 2021, 05:44:06 AM »
For some reason it's not working. I don't really know enough to figure out why  Undecided
Logged
aef
Hero Member
*****

Karma: +70/-46
Offline Offline

Posts: 1601
« Reply #3 on: October 18, 2021, 05:48:59 AM »
which software is this? i am unable to find it by just googling the header text...

can you provide a link please
Logged
BlackT
Hero Member
*****

Karma: +79/-40
Offline Offline

Posts: 1425
« Reply #4 on: October 18, 2021, 06:15:39 AM »
Quote from: aef on October 18, 2021, 05:48:59 AM
which software is this? i am unable to find it by just googling the header text...

can you provide a link please
You get this software with CANalyst-II device

Quote from: JakeGT on October 18, 2021, 05:44:06 AM
For some reason it's not working. I don't really know enough to figure out why  Undecided
I never worked with 8P, but on B6/B7 you receive some data from cluster on CAN lines
Logged
JakeGT
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 21
« Reply #5 on: October 18, 2021, 07:16:05 AM »
Yes it's just software that came with the device.

Not receiving anything but I guess it's because the cluster needs to be woken up first on the wake up pin 5? 
Logged
macxxx
Sr. Member
****

Karma: +30/-1
Offline Offline

Posts: 498
« Reply #6 on: October 18, 2021, 12:14:39 PM »
You have gateway connected? Maybe try to send the frames on Convienence CAN. Are you sure the frame is correct?

I had no problem with starting A6 C6 cluster on table with can frames , I never tried A3 8P with can frame because I had a setup with bordnetz and gateway - if I will find some time I will try to start it using can frames.
Logged
cherry
Sr. Member
****

Karma: +26/-2
Offline Offline

Posts: 260
« Reply #7 on: October 18, 2021, 01:35:42 PM »
Are you sure with the message you send? Normally it´s 07 07 00 00 00. Check also your CAN termination, maybe you need to add a resistor if cluster and tool does not have inside.
Logged
JakeGT
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 21
« Reply #8 on: October 18, 2021, 03:42:44 PM »
apparently ID:575 DLC:2 DATA: 07 00
Logged
simple2me
Jr. Member
**

Karma: +0/-0
Offline Offline

Posts: 28
« Reply #9 on: October 22, 2021, 06:09:17 AM »


I never could get software for the one i bought. took me to some website which would never give me download link. you have link for software. mine is just sitting in the box since i bought another tool.
« Last Edit: October 22, 2021, 06:11:09 AM by simple2me » Logged
JakeGT
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 21
« Reply #10 on: October 22, 2021, 08:26:06 AM »
Quote from: simple2me on October 22, 2021, 06:09:17 AM

I never could get software for the one i bought. took me to some website which would never give me download link. you have link for software. mine is just sitting in the box since i bought another tool.

Mine didn't come with any but this is what I managed to find..

https://easyupload.io/ljo2ha
Logged
simple2me
Jr. Member
**

Karma: +0/-0
Offline Offline

Posts: 28
« Reply #11 on: December 22, 2021, 06:17:24 AM »
just seeing your reply. no file found on the link.
Logged
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 29, 2024, 05:39:01 AM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.019 seconds with 17 queries. (Pretty URLs adds 0s, 0q)