Dev Blog
Forum
Wiki
About
NefMoto
>
Noob Zone
>
Noob Questions
(Moderator:
turboat
) >
ME7.5 how to tell if wideband
Pages: [
1
]
« previous
next »
Author
Topic: ME7.5 how to tell if wideband (Read 2751 times)
wachu
Newbie
Karma: +0/-1
Offline
Posts: 18
ME7.5 how to tell if wideband
« on: November 24, 2021, 08:25:36 AM »
Hello,
I own Audi TT 8N 1.8T AJQ from 2000. I have ME7.5 8N0 906 018 AC (00-08-10) and got few questions:
1. Does my ECU supports a wideband? (If not, how can i tell which ones are narrow and wide?)
2. Does the lower right numbers mean the manufacture date of ECU?
3. What is the best ME7.5 ECU i can find?
I will have a BAM engine with big turbo and i would love to have:
- Wideband o2
- Map switching?
- Easiest one to chiptune
Thank you in advance.
Logged
wachu
Newbie
Karma: +0/-1
Offline
Posts: 18
Re: ME7.5 how to tell if wideband
« Reply #1 on: November 24, 2021, 08:37:18 AM »
Also, i have 3" MAF (0 280 218 065 part number), will it work plug and play with new ECU and current harness? Or i need to modify the MAF harness as well?
Logged
Sandstorm3k
Sr. Member
Karma: +10/-14
Offline
Posts: 403
Re: ME7.5 how to tell if wideband
« Reply #2 on: November 24, 2021, 09:10:37 AM »
1: no, AJQ is narrowband. Though we can rather easily convert this to wideband, my thread is still in the noob section which contains all the info tbh.
2: idk
3: Doesn't matter as long as it's a wideband ECU from a transverse engine.
Swapping a BAM into a (good running) AJQ is a waste of money and time since they both use the 20mm wrist pins. Performance wise AJQ only lacks VVT and wideband, which we can both just swap in using either a complete wideband loom, or just run a few wires.
MAF will work, just copy over MLHFM from BAM file.
Logged
wachu
Newbie
Karma: +0/-1
Offline
Posts: 18
Re: ME7.5 how to tell if wideband
« Reply #3 on: November 24, 2021, 02:12:03 PM »
Thank you very much for help.
My last question is shall i go with 4.2 or 4.9 sensor? Is there a specific part number that we need to look for? As i can see that some of 4.9 bosch sensors are cheaper than others.
Logged
Sandstorm3k
Sr. Member
Karma: +10/-14
Offline
Posts: 403
Re: ME7.5 how to tell if wideband
« Reply #4 on: November 24, 2021, 02:31:50 PM »
Part number; 0258007351
I think it's 4.2
Logged
wachu
Newbie
Karma: +0/-1
Offline
Posts: 18
Re: ME7.5 how to tell if wideband
« Reply #5 on: November 24, 2021, 05:54:53 PM »
Quote from: Sandstorm3k on November 24, 2021, 02:31:50 PM
Part number; 0258007351
I think it's 4.2
Thank you.
I've found that ECUs starting with 4B.. 0906018 are much cheaper than 8N.. (3/4x times in my country)
Is it because they do not support wideband o2?
They've been used is passat b5 / audi a4.
Logged
wachu
Newbie
Karma: +0/-1
Offline
Posts: 18
Re: ME7.5 how to tell if wideband
« Reply #6 on: November 24, 2021, 05:56:50 PM »
Okay sorry.. so sad i cant edit the posts.
4B has different boot and they are not waterproof, hence that they cant be used
Logged
denniss112
Full Member
Karma: +7/-1
Offline
Posts: 114
Audi TT 99' | 180+HP FWD
Re: ME7.5 how to tell if wideband
« Reply #7 on: November 27, 2021, 04:24:05 PM »
I got the AJQ too, I tuned it myself and had the AFR checked during APK(yearly inspection). Went from 180HP to 215, and stock torque to arround 335Nm. Running at 1 BAR boost.
What you could do is buy a 3 inch downpipe with 2 O2 sensor inserts. Then buy a gauge set with O2 sensor so you can monitor.
The difficult route would be a complete conversion where you need a new ECU, new cable harness and sensor. The improvement would be the possibility to tune it based on AFR values.
Logged
Pages: [
1
]
Print
« previous
next »
Jump to:
Please select a destination:
-----------------------------
General
-----------------------------
=> Introductions
=> General Discussion
-----------------------------
Noob Zone
-----------------------------
=> Noob Questions
=> Noob Guides and FAQs
-----------------------------
Technical
-----------------------------
=> NefMoto Software
=> Tuning
===> Documents & Helpers & How To's
===> Community Projects
=> Diagnostics
=> Flashing and Chipping
=> Cluster and Immobilizer
===> ECU EEPROM images
===> Original Cluster dumps
===> Original Cluster dump requests
=> Data Logging
=> Reverse Engineering
=> Communication Protocols
-----------------------------
ECU Files
-----------------------------
=> ECU Definition Files
===> ECU Definition File Requests
=> Original ECU Files
===> Original ECU File Requests
=> Checksum Update Requests
-----------------------------
Vehicles
-----------------------------
=> Vehicle Tech
=> Project Cars
-----------------------------
Regional
-----------------------------
=> Canadian Regional Discussion
=> US Regional Discussion
-----------------------------
Classifieds
-----------------------------
=> For Sale
=> Wanted
=> Services
-----------------------------
Miscellaneous
-----------------------------
=> Off Topic
=> Forum Tech Support
=> Bizarro Messages Posted by Bots and Spammers
Navigation
Home
Help
Login
Register
Personal Tools
April 26, 2024, 01:55:08 AM
Welcome,
Guest
. Please
login
or
register
.
Did you miss your
activation email?
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
Search
Advanced Search
Loading...