Pages: [1]
Author Topic: Bosch EDC17CP14 - XDF Definition Required  (Read 904 times)
Markus67
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 4


« on: January 07, 2022, 12:36:40 PM »

Good evening fellow forumers

I am after an XDF definition file for TunerPro, I do have the ECU BIN file but need the XDF file for the Software, it would be most appreciated if someone could point me in the right direction or perhaps assist me in getting hold of this file

Many thanks in advance, best regards
Mark
Logged
Audiquattro44
Jr. Member
**

Karma: +9/-10
Offline Offline

Posts: 33


« Reply #1 on: January 08, 2022, 05:26:02 AM »

hello send me a DAMOS, A2L or KP file and your original then I can create an XDF for you
Logged
Markus67
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 4


« Reply #2 on: January 08, 2022, 06:48:39 AM »

Firstly thank you for replying, I might be sounding a little thick, but can you not create an XDF file based on the Original file from the ECU?
Logged
Audiquattro44
Jr. Member
**

Karma: +9/-10
Offline Offline

Posts: 33


« Reply #3 on: January 09, 2022, 12:50:57 PM »

is definitely possible but that would take too long and nobody wants to pay for it. Why reinvent the wheel when something is already available
Logged
ruan
Jr. Member
**

Karma: +2/-8
Offline Offline

Posts: 33


« Reply #4 on: January 10, 2022, 10:44:34 AM »

https://github.com/bri3d/a2l2xdf

??
Logged
d3irb
Full Member
***

Karma: +107/-0
Offline Offline

Posts: 138


« Reply #5 on: January 10, 2022, 04:16:18 PM »

Quote

This is my tool, so I'm only talking ill about myself - this isn't there yet.

It will work eventually and has the basics you'd need to make a Bosch A2L -> XDF tool, but I don't think it will work out of the box on EDC17 because the axis definitions in A2L work differently than they do on Continental.

a2l2xdf relies on AXIS_PTS_REF being defined for every axis, which is not true on Bosch where some different axis methods are used.

This tool was made for Continental and works perfectly there, but for Bosch it needs a different axis creation method. I'll get there eventually, it's pretty far down my stack of things to do.

If someone else takes it on and makes a pull request on GitHub I will happily accept it too Smiley
Logged
Markus67
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 4


« Reply #6 on: January 11, 2022, 06:58:20 PM »

is definitely possible but that would take too long and nobody wants to pay for it. Why reinvent the wheel when something is already available

Hi Sir

I have been doing a lot of research, sending emails and I have an SGM file for this ECU, will this help?  It is a Damos file, or at least I think so

Regards
Mark

P.S. If this is what you are looking for, then please let me know how I can upload this to you
Logged
prj
Hero Member
*****

Karma: +456/-125
Offline Offline

Posts: 4392


« Reply #7 on: January 12, 2022, 07:35:13 AM »

Hi Sir

I have been doing a lot of research, sending emails and I have an SGM file for this ECU, will this help?  It is a Damos file, or at least I think so
It is not.
Logged

PM's will not be answered, so don't even try.
Markus67
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 4


« Reply #8 on: January 13, 2022, 12:13:38 PM »

Hi

Sorry  I didnt mean a .sgm file but a .sgo file which I got through a damos download which is why I was wondering whether it will help

Regards
Mark
Logged
prj
Hero Member
*****

Karma: +456/-125
Offline Offline

Posts: 4392


« Reply #9 on: January 13, 2022, 12:20:47 PM »

Hi

Sorry  I didnt mean a .sgm file but a .sgo file which I got through a damos download which is why I was wondering whether it will help

Regards
Mark
No.
Logged

PM's will not be answered, so don't even try.
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.018 seconds with 18 queries. (Pretty URLs adds 0s, 0q)