NefMoto > Noob Zone > Noob Guides and FAQs (Moderator: turboat) > Swap ECU
Pages: [1]
« previous next »
Author Topic: Swap ECU  (Read 10231 times)
vserena82
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 18
« on: March 10, 2022, 03:28:31 PM »
Hello,

is it possible to swap ECU (in my case for VW tiguan 03G 906 016 BT) from one car to another?

How I have to do to make it working? Is enough to remove immobilizer flashing eeprom?

thank you
Logged
hiszpan995
Newbie
*

Karma: +1/-2
Offline Offline

Posts: 9
« Reply #1 on: March 10, 2022, 10:16:21 PM »
if the code is the same, it is enough to remove the immo or encode it.
The second option if you have hardware is to clone the ECU.
Logged
vserena82
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 18
« Reply #2 on: March 11, 2022, 12:08:39 AM »
Quote from: hiszpan995 on March 10, 2022, 10:16:21 PM
if the code is the same, it is enough to remove the immo or encode it.
The second option if you have hardware is to clone the ECU.

Thank you,

there is the possibility to remove immo without open the ecu?
What hardware is needed?
Logged
EanDem
Full Member
***

Karma: +8/-40
Offline Offline

Posts: 78
« Reply #3 on: March 11, 2022, 12:38:08 AM »
Quote from: vserena82 on March 10, 2022, 03:28:31 PM
Hello,

is it possible to swap ECU (in my case for VW tiguan 03G 906 016 BT) from one car to another?

How I have to do to make it working? Is enough to remove immobilizer flashing eeprom?

thank you

Fastest way - do immo with Odis online.
Logged
vserena82
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 18
« Reply #4 on: March 11, 2022, 01:41:06 AM »
Quote from: EanDem on March 11, 2022, 12:38:08 AM
Fastest way - do immo with Odis online.

I have no knowledge about it, what hardware I need? it works on CAN bus or directry on ecu connector?
Logged
prj
Hero Member
*****

Karma: +1072/-480
Offline Offline

Posts: 6034
« Reply #5 on: March 11, 2022, 05:23:07 AM »
03G906016BT is EDC16.
EDC16 can be fully cloned. Via connector with proper tools or by opening the ECU via cheap chinese clones.

If you have no tools and no knowledge of anything, then... well don't do anything.
For every approach you are going to have to pay. And for every approach it is going to cost more than to go to dealer and have them code the ECU to the car.
I wouldn't open these either, because they are usually mounted in plain sight and the casing is completely corroded.
« Last Edit: March 11, 2022, 05:24:51 AM by prj » Logged
PM's will not be answered, so don't even try.
Log your car properly - WinOLS database - Tools/patches
vserena82
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 18
« Reply #6 on: March 12, 2022, 06:40:24 AM »
Quote from: prj on March 11, 2022, 05:23:07 AM
03G906016BT is EDC16.
EDC16 can be fully cloned. Via connector with proper tools [...]

could you tell me what are "proper tools"? Could you tell me hw and sw tools?
I can evaluate to buy them...

I have electronics experience, i have eeprom programmers but nothing for automotive yet.

I have to remove immo in this ecu, the problem is that this one was sealed with silicone and is not possible to remove the board and I have not direct access to eeprom. I have access only to back of board. There is another way to read and write eeprom?

I have just opened a new topic here:
http://nefariousmotorsports.com/forum/index.php?topic=20524.0title=
Logged
prj
Hero Member
*****

Karma: +1072/-480
Offline Offline

Posts: 6034
« Reply #7 on: March 12, 2022, 03:30:34 PM »
If you already opened the thing, and the BDM test points are exposed, you can use some china BDM. Should be easy.
Otherwise a proper flashtool through connector. I think the cheapest will be around 3000 EUR. New Trasdata master with relevant cables and protocol activations.

I mean either way, the proper master tools cost 3000-6000 EUR.
« Last Edit: March 12, 2022, 03:32:18 PM by prj » Logged
PM's will not be answered, so don't even try.
Log your car properly - WinOLS database - Tools/patches
cherry
Sr. Member
****

Karma: +26/-2
Offline Offline

Posts: 260
« Reply #8 on: March 13, 2022, 10:50:43 AM »
Pcmflash does offer EDC16 bench too. You need scanmatik Interface to use it. But in the moment not easy to buy stuff from russia...
Logged
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 22, 2024, 06:18:17 AM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.039 seconds with 18 queries. (Pretty URLs adds 0s, 0q)