Pages: [1] 2 3 ... 5
Author Topic: Need help with my frankturbo tune. logs inside  (Read 53444 times)
savages4
Sr. Member
****

Karma: +10/-5
Offline Offline

Posts: 251


« on: June 24, 2012, 09:49:29 PM »

So I can't seem to get my WOT and high rpm tune to behave..  I feel like I have little boost in the high rpm (above 4000), I logged tonight the best I could with the annoying san diego traffic even at 9:00 at night..  I don't think I was able to satisfy the filters needs but I tried doing some 1st, 2nd, 3rd pulls.  I'm new at the whole ecu-x thing so I'm not having a good time putting the graphs together.. Map and logs attached.
Logged
nyet
Administrator
Hero Member
*****

Karma: +608/-168
Offline Offline

Posts: 12271


WWW
« Reply #1 on: June 25, 2012, 08:14:35 AM »

Those logs are totally worthless.

Get a 3rd gear pull wot from 2500rpm to redline
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
savages4
Sr. Member
****

Karma: +10/-5
Offline Offline

Posts: 251


« Reply #2 on: June 25, 2012, 08:23:00 AM »

Honestly the car isn't making much boost up top so the thing takes forever to run out 3rd gear..  I will give it a try again today, but the traffic around here blows for it.
Logged
nyet
Administrator
Hero Member
*****

Karma: +608/-168
Offline Offline

Posts: 12271


WWW
« Reply #3 on: June 25, 2012, 09:01:41 AM »

Then forget about running it out.

How about staying WOT in third starting at 2500 rpm for longer than 1 second Tongue

And please try to only have the logger running when you are actually doing something worth logging...

In any case, your WGDC is at 10%, which means you are in limp mode.

Any codes?
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
savages4
Sr. Member
****

Karma: +10/-5
Offline Offline

Posts: 251


« Reply #4 on: June 25, 2012, 10:20:26 AM »

Okay did some more runs, with hold WOT in 3rd from 2500 to close to redline twice.  I will go pull the codes now but no check engine light..
Logged
savages4
Sr. Member
****

Karma: +10/-5
Offline Offline

Posts: 251


« Reply #5 on: June 25, 2012, 10:28:13 AM »

I'm getting error code P1557... deviation code obviously because my turbos aren't making over 10 psi! lol  what the hell is going on.
Logged
nyet
Administrator
Hero Member
*****

Karma: +608/-168
Offline Offline

Posts: 12271


WWW
« Reply #6 on: June 25, 2012, 10:39:05 AM »

You are requesting too much boost too soon.

Why are you requesting max boost below 2700 rpm?

Your WGDC is stuck at 10% because it threw a code when your actual can't meet requested ON BOOST RAMP.

Clear the code, and do one pull in 3rd.
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
savages4
Sr. Member
****

Karma: +10/-5
Offline Offline

Posts: 251


« Reply #7 on: June 25, 2012, 10:45:58 AM »

I'm using the rs4 ldrxn as a baseline so I figured my turbos should be able to make close to what the regular bosch k04s are making?  So should I adjust the boost curve to build more gradually and then log again?
Logged
nyet
Administrator
Hero Member
*****

Karma: +608/-168
Offline Offline

Posts: 12271


WWW
« Reply #8 on: June 25, 2012, 11:01:30 AM »

Hmm. I can't tell if your LDRXN is ok.

I'd need to see a log of your car with the DTC cleared to see why it is being set.

If you LDRXN is RS4, and you aren't requesting more than 170 load at 2700rpm, you might be ok.

Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
savages4
Sr. Member
****

Karma: +10/-5
Offline Offline

Posts: 251


« Reply #9 on: June 25, 2012, 11:02:50 AM »

Yeah well the map i'm using it up top, but any how I adjusted the ldrxn to be less aggressive and now i'll go run again.  My wastegates crack at 10 psi, is there a possibility that it's the n75 valve control causing the issues?
Logged
nyet
Administrator
Hero Member
*****

Karma: +608/-168
Offline Offline

Posts: 12271


WWW
« Reply #10 on: June 25, 2012, 11:08:58 AM »

Impossible to know w/o seeing a log if what is happening when your ECU throws the code...
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
savages4
Sr. Member
****

Karma: +10/-5
Offline Offline

Posts: 251


« Reply #11 on: June 25, 2012, 11:12:09 AM »

Okay ill be sure to clear make sure there are no codes before next full wot pull in 3rd. I will post back in a bit, thanks for your help so far much appreciated.
Logged
savages4
Sr. Member
****

Karma: +10/-5
Offline Offline

Posts: 251


« Reply #12 on: June 25, 2012, 11:15:40 AM »

Also both times i've logged, about 10 minutes into the session the car jerks like complete loss of everything and ecm light flashes on rpm gauge, this is only when logging, when this happens the logger throws error code 8... again only happens when im logging and it happened both times and cruising speeds on highway.
Logged
savages4
Sr. Member
****

Karma: +10/-5
Offline Offline

Posts: 251


« Reply #13 on: June 25, 2012, 11:55:28 AM »

Okay I cleared the codes twice and ran two logs with two 3rd gear wot runs.  Went into limp mode both times I believe.  Logs attached as well as revised map.
Logged
nyet
Administrator
Hero Member
*****

Karma: +608/-168
Offline Offline

Posts: 12271


WWW
« Reply #14 on: June 25, 2012, 01:24:59 PM »

you're triggering the DTC long before I see it in a 3rd gear pull... so all 3rd gear pulls have 10% dc

STAY OUT OF BOOST until you can start your pull...

I dont know why you are requesting so much load/boost at such low accel ped positions.
« Last Edit: June 25, 2012, 01:28:53 PM by nyet » Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
Pages: [1] 2 3 ... 5
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.018 seconds with 18 queries. (Pretty URLs adds 0.001s, 0q)