mourison
Full Member
Karma: +0/-30
 Offline
Posts: 95
|
 |
« on: November 02, 2023, 11:50:45 PM »
|
|
|
Is there any kind soul out there that can show me how to turn off sai?
I tried turning off the eskonf and disconnecting the sai pump and solenoid 112 but the car still gives the DTC and bad starts.
now its AA FF 00 30 FF FB 3C
Thank you
|
|
|
|
|
Logged
|
|
|
|
zCruuz
Full Member
Karma: +7/-0
Offline
Posts: 80
|
|
« Reply #1 on: November 03, 2023, 12:56:39 AM »
|
|
|
You are turning the power output to the Relais off and now you are wondering, why you still get DTCs... Read the wiki https://s4wiki.com/wiki/Tuning |
|
|
|
|
Logged
|
|
|
|
mourison
Full Member
Karma: +0/-30
Offline
Posts: 95
|
|
« Reply #2 on: November 03, 2023, 04:13:56 AM »
|
|
|
Precisely that the relays are not switched off, because when connected, they are switched on during a cold start.
but in eskonf everything should be set
|
|
|
|
|
Logged
|
|
|
|
fknbrkn
Hero Member
Karma: +185/-23
Offline
Posts: 1454
mk4 1.8T AUM
|
|
« Reply #3 on: November 03, 2023, 06:35:46 AM »
|
|
|
Precisely that the relays are not switched off, because when connected, they are switched on during a cold start.
but in eskonf everything should be set
Eskonf is just a circuit diagnose Read the wiki |
|
|
|
|
Logged
|
|
|
|
R32Dude
Full Member
Karma: +45/-10
Offline
Posts: 248
|
|
« Reply #4 on: November 03, 2023, 05:02:01 PM »
|
|
|
Do you want to turn it off only or remove components as well?
|
|
|
|
|
Logged
|
|
|
|
mourison
Full Member
Karma: +0/-30
Offline
Posts: 95
|
|
« Reply #5 on: November 04, 2023, 12:10:24 AM »
|
|
|
I would like to disconnect the sai connector and the 112 solenoid and leave the wiring in the car, but I would like the car to not have cold start problems and not display an error :/
|
|
|
|
|
Logged
|
|
|
|
R32Dude
Full Member
Karma: +45/-10
Offline
Posts: 248
|
|
« Reply #6 on: November 04, 2023, 12:53:23 AM »
|
|
|
A resistor in the place of the N112 and the electric motor might do the job.
|
|
|
|
|
Logged
|
|
|
|
zCruuz
Full Member
Karma: +7/-0
Offline
Posts: 80
|
|
« Reply #7 on: November 04, 2023, 01:11:31 AM »
|
|
|
Code it out properly and you will archive this. But nobody will come and Tell you what to do. Everything is up on Wiki and nef. If you are not capable of scrolling down on Wiki down to sai, read and do what's written there. Determing what resistors are needed might also be a to heavy task.
Gesendet von meinem SM-G991B mit Tapatalk
|
|
|
|
|
Logged
|
|
|
|
mourison
Full Member
Karma: +0/-30
Offline
Posts: 95
|
|
« Reply #8 on: November 05, 2023, 01:53:19 PM »
|
|
|
Ok, according to the s4 wiki I removed.
Is it possible to look at the bin to see if everything is ok including chk?
WinOls says there are bad checksums and the car won't start, but me7sum says it doesn't see a problem :/
Thank you
|
|
|
|
« Last Edit: November 05, 2023, 02:18:10 PM by mourison »
|
Logged
|
|
|
|
zCruuz
Full Member
Karma: +7/-0
Offline
Posts: 80
|
|
« Reply #9 on: November 05, 2023, 02:34:09 PM »
|
|
|
Noread in ols, so i can't check. Don't know if it affects me7sum, you might deactivate it and try cs again.
If CS are correct just flash and try...
|
|
|
|
|
Logged
|
|
|
|
mourison
Full Member
Karma: +0/-30
Offline
Posts: 95
|
|
« Reply #10 on: November 05, 2023, 02:52:37 PM »
|
|
|
I'm sorry, I didn't notice that in the winols settings, I canceled all the settings, so maybe it should work now.
Below I describe what I did, but after exporting the bin and re-opening, ols gives me bad chk and won't fix them
"winols not all the expected checksums were found correction may be incomplete"
after uploading to the car, the car won't start and the vcds won't connect to the unit.
After playing on the original flash, everything works
I think there is something really wrong with chk
I am also attaching the original list + kp that I use
AA FF 00 30 FF F8 30 => AA FF 00 30 FF FB 3C
CDSLS to 0
CWKONABG to 0
MSLUB => all 0
MSLBAS => all 0
|
|
|
|
« Last Edit: November 05, 2023, 03:41:32 PM by mourison »
|
Logged
|
|
|
|
mourison
Full Member
Karma: +0/-30
Offline
Posts: 95
|
|
« Reply #11 on: November 05, 2023, 02:57:37 PM »
|
|
|
I'm sorry, I didn't notice that in the winols settings, I canceled all the settings, so maybe it should work now.
Below I describe what I did, but after exporting the bin and re-opening, ols gives me bad chk and won't fix them
"winols not all the expected checksums were found correction may be incomplete"
I am also attaching the original list + kp that I use
AA FF 00 30 FF F8 30 => AA FF 00 30 FF FB 3C
CDSLS to 0
CWKONABG to 0
MSLUB => all 0
MSLBAS => all 0
|
|
|
|
|
Logged
|
|
|
|
JeanAwt
Full Member
Karma: +10/-12
Offline
Posts: 241
|
|
« Reply #12 on: November 05, 2023, 11:33:44 PM »
|
|
|
try this
cheksums ok
*** DONE! 0 error(s) in C:\Users\\Downloads\WinOLS (10068.ols (SAI off_ALL) -
363908)! ***
|
|
|
|
|
Logged
|
A4 B5 avant 1.8T 2000 NO QUATTRO
|
|
|
mourison
Full Member
Karma: +0/-30
Offline
Posts: 95
|
|
« Reply #13 on: November 05, 2023, 11:39:57 PM »
|
|
|
winols opened this bin without errors?
Winols gives me an error even though I have plugins on chk
bin with 032hjworks fine .. maybe broken flash ?
|
|
|
|
« Last Edit: November 05, 2023, 11:44:06 PM by mourison »
|
Logged
|
|
|
|
mourison
Full Member
Karma: +0/-30
Offline
Posts: 95
|
|
« Reply #14 on: November 05, 2023, 11:43:08 PM »
|
|
|
img
|
|
|
|
|
Logged
|
|
|
|
|
