Pages: [1]
Author Topic: Definition file for 0261207696 1037382338 cw_can_r me7.1.1 cayenne  (Read 1071 times)
Cayenne521
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 5



Im looking for an Definition file for an 06 Turbo S Me7.1.1 0261207696 1037382338 8te2ass20000188

I want to delete complete tcu from can bus.
I think cw_can_r will do this.

I located :
CW_CAN_R_0_A  at 8136F8
CW_CAN_R_1_A at 8136FA

But im not sure about this and what I need to change I had a Look at the FR and I think 0A and 1A is not enough?

I hope someone can help me



Logged
Artemisia
Newbie
*

Karma: +2/-0
Offline Offline

Posts: 9



« Reply #1 on: June 12, 2024, 07:27:40 PM »

This should do the trick

Logged
Cayenne521
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 5


« Reply #2 on: June 13, 2024, 02:58:49 AM »

This should do the trick


Thanks, for the help.

Yesterday I looked at it again with an mappack and I just changed the last two bits to 0  from cw_can_r  and changed cwgc to 15 . It works without abs light

I think you basically did the same think ? I have a Look at your file later then I have my PC winols.

Only error left is p0501 speed Sensor implausible signal, maybe a lose plug or something to do with the manual swap.
« Last Edit: June 13, 2024, 03:02:36 AM by Cayenne521 » Logged
_nameless
Hero Member
*****

Karma: +327/-454
Offline Offline

Posts: 2730



« Reply #3 on: June 13, 2024, 03:42:37 AM »

Set cwggvfzg =2 and that will pull vss from can via wheel speed sensors
Logged

If you are in the market for a tune and would like the ease of downloading and flashing a dyno tested tune for a fair price check out https://instatune.sellfy.store/
Cayenne521
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 5


« Reply #4 on: June 15, 2024, 03:29:18 AM »

Set cwggvfzg =2 and that will pull vss from can via wheel speed sensors

2 is not possible max value is 1 but then it will take vss from abs and this will work too or I understand the FR wrong ?
Logged
MirXas
Full Member
***

Karma: +2/-6
Offline Offline

Posts: 73



« Reply #5 on: June 15, 2024, 01:54:58 PM »

ggvfzg max value is definitely not "1". Just my two cents.
Logged
Artemisia
Newbie
*

Karma: +2/-0
Offline Offline

Posts: 9



« Reply #6 on: June 15, 2024, 07:44:37 PM »

2 is not possible max value is 1 but then it will take vss from abs and this will work too or I understand the FR wrong ?

Look at 0x10453, change 0x18 to 0x02
Logged
Cayenne521
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 5


« Reply #7 on: June 16, 2024, 10:18:44 AM »

ggvfzg max value is definitely not "1". Just my two cents.

Ofc you are right, not sure what I did maybe I tried editing in 1bit bin  Roll Eyes

Look at 0x10453, change 0x18 to 0x02

You are absolutly right with this one.

Now I am at CWGGEGAS and so on for the clutch switch.
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.017 seconds with 18 queries. (Pretty URLs adds 0s, 0q)