NefMoto > Noob Zone > Noob Questions (Moderator: turboat) > adaptation sequence for engine
Pages: [1]
« previous next »
Author Topic: adaptation sequence for engine  (Read 273 times)
gibcou97
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 3
« on: November 08, 2024, 10:48:57 AM »
so i have done timing on a caeb engine code and i keep getting a p0016 camshaft correlation code. i have retimed it verified I'm tdc and cams are locked at tdc, chain is correct and tensioner/ guides are correct. Is  there a specific sequence for adaptation, if so what is it?
thank you
Logged
prj
Hero Member
*****

Karma: +1069/-476
Offline Offline

Posts: 6011
« Reply #1 on: November 08, 2024, 11:17:54 AM »
If you get that code then timing is out, simple as that.
Logged
PM's will not be answered, so don't even try.
Log your car properly - WinOLS database - Tools/patches
gibcou97
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 3
« Reply #2 on: November 08, 2024, 11:54:35 AM »
Quote from: prj on November 08, 2024, 11:17:54 AM
If you get that code then timing is out, simple as that.
how would you verify tdc on the crank, cam, and piston?  the intake and exhaust cams just give you the little marks but don't have anywhere to line up the marks on the valve cover/ cam cradle
« Last Edit: November 08, 2024, 11:58:59 AM by gibcou97 » Logged
prj
Hero Member
*****

Karma: +1069/-476
Offline Offline

Posts: 6011
« Reply #3 on: November 08, 2024, 12:25:23 PM »
Take the OEM manual, buy all the required factory tools, and time it correctly.
I bet you're eyeballing shit that has no business being eyeballed.
Logged
PM's will not be answered, so don't even try.
Log your car properly - WinOLS database - Tools/patches
cherry
Sr. Member
****

Karma: +26/-2
Offline Offline

Posts: 259
« Reply #4 on: November 08, 2024, 12:29:31 PM »
You compared tdc from pulley or piston? This is a common mistake if not using correct pulley tools...

The marks on camshaft have a defined distance in repair instructions, did you measure it? Did you read these instructions?
Logged
gibcou97
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 3
« Reply #5 on: November 08, 2024, 12:43:19 PM »
Quote from: cherry on November 08, 2024, 12:29:31 PM
You compared tdc from pulley or piston? This is a common mistake if not using correct pulley tools...

The marks on camshaft have a defined distance in repair instructions, did you measure it? Did you read these instructions?
started with pulley and then verified it off piston and cam gear mark.
i was unable to find them in my repair system do you have the link for it.
Logged
cherry
Sr. Member
****

Karma: +26/-2
Offline Offline

Posts: 259
« Reply #6 on: November 08, 2024, 01:16:44 PM »
Just google elsaonline for some russian website or login to paid official audi erwin website.
Logged
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 12, 2024, 11:37:15 PM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.027 seconds with 17 queries. (Pretty URLs adds 0.004s, 0q)