ME7.5 Lambda goes to 0.75 at idle, engine protection feature?

Pages: 1 [2] 3

« previous next »

Author

Topic: ME7.5 Lambda goes to 0.75 at idle, engine protection feature? (Read 25169 times)

jtorres

Jr. Member

Karma: +2/-0
Offline

Offline

Posts: 36

	Re: ME7.5 Lambda goes to 0.75 at idle, engine protection feature? « Reply #15 on: September 21, 2012, 07:59:36 AM »

Quote from: littco on September 21, 2012, 05:42:49 AM

Is the loom from the matching car the ecu came from?

I am not sure, ecu is from an AWW i will check from which car the loom came. we have the donor car at hand. Some times i though there is a wire or signal that is incorrectly feed to the ECU

from hipeka: Does ECU shows actual 1.00 or 0.75 (Data logging, not measured) ?

Yes at the block 31 the actual lambda showed .75 and requested 1.000, and confirmed it is pig rich with an aem wideband.


	Logged

matchew

Hero Member

Karma: +47/-22
Offline

Offline

Posts: 503

	Re: ME7.5 Lambda goes to 0.75 at idle, engine protection feature? « Reply #16 on: September 21, 2012, 08:22:42 AM »

What is lambda correction factor in block 99?


	Logged

jtorres

Jr. Member

Karma: +2/-0
Offline

Offline

Posts: 36

	Re: ME7.5 Lambda goes to 0.75 at idle, engine protection feature? « Reply #17 on: September 21, 2012, 08:29:11 AM »

Quote from: matchew on September 21, 2012, 08:22:42 AM

What is lambda correction factor in block 99?

i will check


	Logged

phila_dot

Hero Member

Karma: +173/-11
Offline

Offline

Posts: 1709

	Re: ME7.5 Lambda goes to 0.75 at idle, engine protection feature? « Reply #18 on: September 21, 2012, 10:21:38 AM »

Quote from: matchew on September 21, 2012, 08:22:42 AM

What is lambda correction factor in block 99?

Just curious, why 99 and not 32/33?


	Logged

jtorres

Jr. Member

Karma: +2/-0
Offline

Offline

Posts: 36

	Re: ME7.5 Lambda goes to 0.75 at idle, engine protection feature? « Reply #19 on: September 21, 2012, 11:17:42 AM »

Just checked car has a AWP wiring loom and we are using an AWW ECU (06A906032KP). Can be that the cause of the trouble?

Is a swapped engine to a MK2 Golf remember.


	Logged

jtorres

Jr. Member

Karma: +2/-0
Offline

Offline

Posts: 36

	Re: ME7.5 Lambda goes to 0.75 at idle, engine protection feature? « Reply #20 on: September 21, 2012, 11:22:38 AM »

found this harness comparison at vortex but cannot find something really different from AWW to AWP

http://forums.vwvortex.com/showthread.php?5049235-APH-AWW-AWP-AWV-wiring-harness-comparison


	Logged

k0mpresd

Hero Member

Karma: +146/-54
Offline

Offline

Posts: 1655

	Re: ME7.5 Lambda goes to 0.75 at idle, engine protection feature? « Reply #21 on: September 21, 2012, 02:56:19 PM »

pretty sure 032kp is awp.


	Logged

jtorres

Jr. Member

Karma: +2/-0
Offline

Offline

Posts: 36

	Re: ME7.5 Lambda goes to 0.75 at idle, engine protection feature? « Reply #22 on: September 21, 2012, 09:32:43 PM »

Quote from: k0mpresd on September 21, 2012, 02:56:19 PM

pretty sure 032kp is awp.

You are completely right, not sure why i was confused with that!

What can be happen there? the car starts fine and after a minute the lambda starts to move from 1.000 to .75 and stays there.

At block 99 the lambda correction is -26%. Inyection time at idle is around 1.76 ms when lambda shows 0.75, little high as the regular inyection time at idle is around 1.3 ms.

I did checked the fuel return to the tank is OK and tried anoter FPR thinking it can be stuck close. Also tested another MAP sensor today with no luck. Several wires from the ECU connector was checked for continuity, also tried another lambda probe. There is no dtc´s other than the abs comunication and the data bus. N112, N80 and N249 solenoids were connected and DTC´s are off now.

I am thinking that maybe some input are feeding the ECU incorrectly but checked the IAT and ECT and they have regular readings when connected and disconnected. I did also tested with the MAF plugged and unplugged, samo samo.

I am kind of lost, this is not my first 1.8T swap, thinking to try another harness now.


	Logged

matchew

Hero Member

Karma: +47/-22
Offline

Offline

Posts: 503

	Re: ME7.5 Lambda goes to 0.75 at idle, engine protection feature? « Reply #23 on: September 21, 2012, 09:48:52 PM »

Is the engine, MAF and ECU from the same donor car?


	Logged

jtorres

Jr. Member

Karma: +2/-0
Offline

Offline

Posts: 36

	Re: ME7.5 Lambda goes to 0.75 at idle, engine protection feature? « Reply #24 on: September 21, 2012, 09:51:18 PM »

Yes, but anyway thinking of a failed MAF, when disconnected it is not suposed to go that rich at idle


	Logged

prj

Hero Member

Karma: +1072/-485
Offline

Offline

Posts: 6040

	Re: ME7.5 Lambda goes to 0.75 at idle, engine protection feature? « Reply #25 on: September 22, 2012, 02:43:51 AM »

Measure your fuel pressure in rail, leave ECU alone for now.


	Logged

PM's will not be answered, so don't even try.
Log your car properly - WinOLS database - Tools/patches

Gonzo

Sr. Member

Karma: +21/-30
Offline

Offline

Posts: 483

	Re: ME7.5 Lambda goes to 0.75 at idle, engine protection feature? « Reply #26 on: September 22, 2012, 07:01:25 AM »

You need to resistor emission items.


	Logged

phila_dot

Hero Member

Karma: +173/-11
Offline

Offline

Posts: 1709

	Re: ME7.5 Lambda goes to 0.75 at idle, engine protection feature? « Reply #27 on: September 22, 2012, 09:02:32 AM »

Quote from: Gonzo on September 22, 2012, 07:01:25 AM

You need to resistor emission items.

How can it be related to emmisions components if target Lambda is 1?

OP, are you sure the ECU matches all the hardware (i.e. injectors)?


	Logged

k0mpresd

Hero Member

Karma: +146/-54
Offline

Offline

Posts: 1655

	Re: ME7.5 Lambda goes to 0.75 at idle, engine protection feature? « Reply #28 on: September 22, 2012, 09:41:29 AM »

plus he already said they are plugged in.


	Logged

jtorres

Jr. Member

Karma: +2/-0
Offline

Offline

Posts: 36

	Re: ME7.5 Lambda goes to 0.75 at idle, engine protection feature? « Reply #29 on: September 22, 2012, 10:12:01 PM »

Yes oem injectors with oem tune. All emissions are resistored now: N112, N80. Also N249.

There is no DTC´s other than the abs and data bus. I am thinking on a bad harness or a bad connection that inputs a wrong signal or something like that. I will test another loom cause this thing is driving me crazy.


	Logged

Pages: 1 [2] 3

« previous next »

Jump to:

Navigation

Personal Tools

November 29, 2024, 07:15:33 PM

Welcome, Guest. Please login or register.
Did you miss your activation email?

Navigation

Personal Tools

Search