Pages: [1]
Author Topic: Flashing problem with Nefmoto  (Read 8408 times)
hipeka
Full Member
***

Karma: +1/-1
Offline Offline

Posts: 85


« on: November 16, 2012, 10:33:06 PM »

Hi

I have used Nefmoto software for a while to flash my ECU. Last two times i have had problems with flahs erase.

Nefmoto log show this:
16.marras.2012 10:49:26.166: LOG: Checksum is correct.
16.marras.2012 10:49:26.166: USER: Flash checksum matches new data, flashing is unnecessary, but flashing anyway.
16.marras.2012 10:49:26.166: USER: Requesting flash memory erase for address range 0x008F0000 to 0x008F7FFF.
16.marras.2012 10:49:26.176: LOG: Sent message with service ID StartRoutineByLocalIdentifier
16.marras.2012 10:49:26.186: LOG: Received message with service ID: StartRoutineByLocalIdentifierPositiveResponse
16.marras.2012 10:49:26.196: LOG: Sent message with service ID RequestRoutineResultsByLocalIdentifier
16.marras.2012 10:49:26.216: LOG: Received message with service ID: NegativeResponse
16.marras.2012 10:49:26.216: LOG: Received negative response for service ID: RequestRoutineResultsByLocalIdentifier, with response code: GeneralReject
16.marras.2012 10:49:26.216: USER: Erase flash memory routine did not start or complete correctly.
16.marras.2012 10:49:28.700: LOG: Sent message with service ID TesterPresent
16.marras.2012 10:49:28.720: LOG: Received message with service ID: TesterPresentPositiveReponse
16.marras.2012 10:49:31.213: LOG: Sent message with service ID TesterPresent
16.marras.2012 10:49:31.233: LOG: Received message with service ID: TesterPresentPositiveReponse
16.marras.2012 10:49:33.737: LOG: Sent message with service ID TesterPresent
16.marras.2012 10:49:33.757: LOG: Received message with service ID: TesterPresentPositiveReponse
16.marras.2012 10:49:36.241: LOG: Sent message with service ID TesterPresent
16.marras.2012 10:49:36.261: LOG: Received message with service ID: TesterPresentPositiveReponse
16.marras.2012 10:49:38.744: LOG: Sent message with service ID TesterPresent
16.marras.2012 10:49:38.764: LOG: Received message with service ID: TesterPresentPositiveReponse
16.marras.2012 10:49:41.248: LOG: Sent message with service ID TesterPresent
16.marras.2012 10:49:41.278: LOG: Received message with service ID: TesterPresentPositiveReponse
16.marras.2012 10:49:43.751: LOG: Sent message with service ID TesterPresent
16.marras.2012 10:49:43.771: LOG: Received message with service ID: TesterPresentPositiveReponse
16.marras.2012 10:49:46.255: LOG: Sent message with service ID TesterPresent
16.marras.2012 10:49:46.275: LOG: Received message with service ID: TesterPresentPositiveReponse
16.marras.2012 10:49:48.759: LOG: Sent message with service ID TesterPresent
16.marras.2012 10:49:48.789: LOG: Received message with service ID: TesterPresentPositiveReponse
16.marras.2012 10:49:49.219: LOG: User Prompt - Title: Sector Erase Failed Message: Failed to erase the memory sector. The new data being flashed likely conflicts with the ECU's persistent data. The persistent ECU data can be replaced by erasing the entire flash memory before programming. If the ECU may contains a non-standard flash memory chip, it could be causing the erase to fail.

Press Yes, to erase the entire ECU flash memory and restart the flashing process.
Press No, to skip flashing this sector and continue the flashing process.
Press Cancel, to abort the flashing process.

WARNING: Only erase the entire flash memory if you have a good communication connection with the ECU. If flashing fails after erasing the entire flash memory, it is likely the ECU will no longer boot, and will have to be reflashed on the bench using boot mode. This software does NOT support boot mode. Result: CANCEL
16.marras.2012 10:49:49.219: USER: Writing ECU flash memory failed.
16.marras.2012 10:49:49.400: USER: 100% complete. 


What should i do to get this work again?
Logged
ddillenger
Hero Member
*****

Karma: +641/-21
Offline Offline

Posts: 5640


« Reply #1 on: November 16, 2012, 11:02:55 PM »

Do you have the car hooked up to an external power supply?
Logged

Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM
hipeka
Full Member
***

Karma: +1/-1
Offline Offline

Posts: 85


« Reply #2 on: November 17, 2012, 01:57:36 AM »

Do you have the car hooked up to an external power supply?

Yes. Modified booster with very stable 14,0V.
Logged
hipeka
Full Member
***

Karma: +1/-1
Offline Offline

Posts: 85


« Reply #3 on: November 18, 2012, 02:25:26 AM »

I just press Yes when this message appear and everything went just fine.


Press Yes, to erase the entire ECU flash memory and restart the flashing process.
Press No, to skip flashing this sector and continue the flashing process.
Press Cancel, to abort the flashing process.

WARNING: Only erase the entire flash memory if you have a good communication connection with the ECU. If flashing fails after erasing the entire flash memory, it is likely the ECU will no longer boot, and will have to be reflashed on the bench using boot mode. This software does NOT support boot mode. Result: CANCEL

« Last Edit: December 04, 2012, 07:43:13 AM by hipeka » Logged
hipeka
Full Member
***

Karma: +1/-1
Offline Offline

Posts: 85


« Reply #4 on: December 01, 2012, 06:00:59 AM »

Can Tony or somebody who knows this program tell why it start doing this every time i try flashing. This use to works without any errors before.
Logged
hipeka
Full Member
***

Karma: +1/-1
Offline Offline

Posts: 85


« Reply #5 on: December 04, 2012, 07:44:20 AM »

I reinstall drivers and Nefmoto software. Now it's working like before.
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.015 seconds with 16 queries. (Pretty URLs adds 0s, 0q)