kolbenmann
Newbie
Karma: +0/-0
 Offline
Posts: 10
|
 |
« on: January 29, 2013, 05:20:34 PM »
|
|
|
Hello:
I just swapped a new instrument cluster on a project and now I need to immo off this file.
I hope someone could give me a hand
|
|
|
|
« Last Edit: February 13, 2013, 12:08:16 PM by nyet »
|
Logged
|
|
|
|
ddillenger
Moderator
Hero Member
Karma: +641/-21
Offline
Posts: 5640
|
|
« Reply #1 on: January 29, 2013, 05:22:44 PM »
|
|
|
oooh-I can do this.
Two seconds.
|
|
|
|
|
Logged
|
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
|
|
|
ddillenger
Moderator
Hero Member
Karma: +641/-21
Offline
Posts: 5640
|
|
« Reply #2 on: January 29, 2013, 05:39:42 PM »
|
|
|
Try this.
|
|
|
|
|
Logged
|
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
|
|
|
kolbenmann
Newbie
Karma: +0/-0
Offline
Posts: 10
|
|
« Reply #3 on: January 29, 2013, 06:42:09 PM »
|
|
|
Try this.
WOW that was fast!!!  thanks a lot for your support, I'll test right away and let you know |
|
|
|
|
Logged
|
|
|
|
|
aef
|
|
« Reply #4 on: January 30, 2013, 03:05:15 AM »
|
|
|
Kolbenmann im not sure if you know this but you can check the immo with vagcom at channel 91.
With my method, the immo off file would look a little different. So please try and report back!
|
|
|
|
|
Logged
|
|
|
|
icezero
Full Member
Karma: +7/-0
Offline
Posts: 129
|
|
« Reply #5 on: January 30, 2013, 05:06:03 AM »
|
|
|
@aef the off file is ok and worked 100% i have done it on same way :-)
|
|
|
|
|
Logged
|
|
|
|
LechnerTuning
Newbie
Karma: +0/-0
Offline
Posts: 10
|
|
« Reply #6 on: March 17, 2013, 01:54:12 AM »
|
|
|
Hello,
we have ME3.8.3 here, its the 24C02 8 pin eprom right, which programer do you use to read/write it, we have the willem here but no suitable socket available ?
I heard that there are programers which can read/write this 24C02 even if they are still on the pcb ?
Thank you
|
|
|
|
« Last Edit: March 17, 2013, 02:19:24 AM by LechnerTuning »
|
Logged
|
|
|
|
|
k0mpresd
|
|
« Reply #7 on: March 17, 2013, 04:47:40 AM »
|
|
|
gq3x + test clip.
|
|
|
|
|
Logged
|
|
|
|
LechnerTuning
Newbie
Karma: +0/-0
Offline
Posts: 10
|
|
« Reply #8 on: March 17, 2013, 07:54:49 AM »
|
|
|
Anybody has the connections ?
|
|
|
|
|
Logged
|
|
|
|
|
|
Drehkraft
Jr. Member
Karma: +9/-0
Offline
Posts: 46
|
|
« Reply #10 on: March 17, 2013, 09:35:16 AM »
|
|
|
|
|
|
|
|
Logged
|
|
|
|
Drehkraft
Jr. Member
Karma: +9/-0
Offline
Posts: 46
|
|
« Reply #11 on: March 17, 2013, 09:36:29 AM »
|
|
|
Just one note - you usually have to apply + power to the W pin (write protect). An unpowered ECU normally holds the line down. I just jumper power from the + pin to that one.
|
|
|
|
|
Logged
|
|
|
|
LechnerTuning
Newbie
Karma: +0/-0
Offline
Posts: 10
|
|
« Reply #12 on: March 17, 2013, 10:49:09 PM »
|
|
|
Isnt there any chance to connect without this adapter, it will take weeks until it will arrive here.
So just soldering the wires direct to the Eeprom and connect it to GQ3X ?
|
|
|
|
|
Logged
|
|
|
|
|
aef
|
|
« Reply #13 on: March 18, 2013, 05:21:42 AM »
|
|
|
Yes it is possible. Search for the 24c02 in your GQ Software and you will see a small picture where to place the chip and the direction.
|
|
|
|
|
Logged
|
|
|
|
LechnerTuning
Newbie
Karma: +0/-0
Offline
Posts: 10
|
|
« Reply #14 on: April 10, 2013, 04:45:06 AM »
|
|
|
Hello,
orderd the stuff from mcumall but when I try to read it, it just reads out zeros.
But I assume its corrected ok because when I completely remove it then it just reads zero.
Anybody met this before ?
|
|
|
|
|
Logged
|
|
|
|
|
