Pages: 1 ... 8 9 [10] 11
Author Topic: Recommended USB VAG KKL Cables  (Read 390518 times)
ZakDodge
Jr. Member
**

Karma: +2/-0
Offline Offline

Posts: 42


« Reply #135 on: October 11, 2019, 11:20:45 PM »

Has anyone found a Galletto cable with a proper digitally signed driver for use with Win 10?

I use a $12 galletto cable off of amazon. works with windows 10. Sometimes ill flash my ross-tech cable to the galletto .ept file and that works even. I have tried to use the Vag K+ Can Commander cables with no luck but those work with me7logger.
Logged
GolfSportWagen
Full Member
***

Karma: +10/-10
Offline Offline

Posts: 100


« Reply #136 on: October 12, 2019, 02:55:43 PM »

Thanks for the reply. Do you have a link to the source of the Galletto/Win 10 viable cable? Are you using the drivers included with the Galletto CD?
« Last Edit: October 12, 2019, 03:19:16 PM by GolfSportWagen » Logged
RicarGli
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 18


« Reply #137 on: October 19, 2019, 11:32:46 AM »

I just bought his cable which worked flawlessly with Nefmoto (https://www.ebay.com/itm/FTDI-FT232RL-VAG-COM-KKL-409-1-OBD2-KWP2000-ISO9141-USB-FOR-VW-AUDI/273510962411?_mwBanner=1&ul_ref=https%3A%2F%2Frover.ebay.com%2Frover%2F0%2F0%2F0%3Fmpre%3Dhttps%253A%252F%252Fwww.ebay.com%252Fulk%252Fitm%252F273510962411%26rvr_id%3D0%26rvr_ts%3De54a34de16d0aaa2893330f1fff58621&ul_noapp=true&pageci=5875c070-97b8-49c5-8f0f-58c3a5e3a56d&epid=1660061025)
Logged
GolfSportWagen
Full Member
***

Karma: +10/-10
Offline Offline

Posts: 100


« Reply #138 on: October 19, 2019, 02:56:54 PM »

Thanks for the link. I have a K-Line cable that is currently working on ME 7.1 ECUs but I cannot find any Galletto cable with proper drivers for Win 10 which is desired for reading/flashing in boot mode.
Logged
316LV
Full Member
***

Karma: +12/-2
Offline Offline

Posts: 150


« Reply #139 on: October 20, 2019, 03:14:46 PM »

Thanks for the link. I have a K-Line cable that is currently working on ME 7.1 ECUs but I cannot find any Galletto cable with proper drivers for Win 10 which is desired for reading/flashing in boot mode.

If you have a working cable, you can just modify Galletto to work with it. No separate cable needed. Here is a link from the late great Daz on how to do it:

http://nefariousmotorsports.com/forum/index.php?topic=3088.msg30597#msg30597

Don't both messing with the cable serial. Just read yours and then use a hex editor on the Galletto exe to input it, save the exe and you are up and going... I've been doing it that way through my last 4 cables (they seem to die when stored in my glovebox - Chinese quality!).
Logged

Go ahead and give me negative karma... I don't care if you like what I post princess.
GolfSportWagen
Full Member
***

Karma: +10/-10
Offline Offline

Posts: 100


« Reply #140 on: October 20, 2019, 03:40:10 PM »

If you have a working cable, you can just modify Galletto to work with it. No separate cable needed. Here is a link from the late great Daz on how to do it:

http://nefariousmotorsports.com/forum/index.php?topic=3088.msg30597#msg30597

Don't both messing with the cable serial. Just read yours and then use a hex editor on the Galletto exe to input it, save the exe and you are up and going... I've been doing it that way through my last 4 cables (they seem to die when stored in my glovebox - Chinese quality!).

Thanks for the link. I'll look into it and see if we can move forward.
« Last Edit: October 20, 2019, 08:02:37 PM by GolfSportWagen » Logged
CrashKrazz
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 10


« Reply #141 on: April 21, 2020, 03:19:12 PM »

Is there any reason the FT231X chip would not be compatible? it appears to support the same drivers as far as I can tell.
Logged
masterb
Newbie
*

Karma: +0/-3
Offline Offline

Posts: 4


« Reply #142 on: May 09, 2020, 11:14:40 PM »


is also Tactrix Openport supportet ?
Logged
d3irb
Full Member
***

Karma: +131/-1
Offline Offline

Posts: 185


« Reply #143 on: May 11, 2020, 10:17:03 AM »

is also Tactrix Openport supportet ?

No. Only FTDI based cables are supported.

This is because NefMoto uses FTDI FTD2XX DLLs for serial communication. I think this was done mostly to allow the EEPROM to be used for license checking. Now that NefMoto is open source ,it shouldn't be too hard to allow it to support generic COM cables.

However, Tactrix would be more challenging to support than generic COM cables because it does not use a serial communication driver but rather the J2534 diagnostics protocol.
Logged
Rick81
Full Member
***

Karma: +0/-10
Offline Offline

Posts: 75


« Reply #144 on: May 23, 2021, 11:57:47 PM »

I tried my tactrix cable and I couldn't connect

Sent from my CPH1931 using Tapatalk

Logged
markhodges78
Jr. Member
**

Karma: +0/-0
Offline Offline

Posts: 32


« Reply #145 on: December 31, 2021, 12:11:52 PM »

Could anyone recommend a cable that would work for this software?

Thanks in advance

Mark
Logged
rdrage
Jr. Member
**

Karma: +13/-1
Offline Offline

Posts: 29


« Reply #146 on: January 08, 2022, 06:48:03 AM »

Could anyone recommend a cable that would work for this software?

Thanks in advance

Mark


Hello ..

I have been working with me7 for 12-13 years, tested several cables. This one is best. Never had any problems with all the me7 programs Smiley

https://www.ebay.de/itm/131620888619?hash=item1ea537602b:g:XiAAAOSwKIdaaZRb


Logged
bonilla
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 4


« Reply #147 on: February 11, 2022, 07:09:24 AM »

I just purchased the following cable https://www.ebay.it/itm/164401045711 but I am unable to have it shown in NefMoto 1.9.4.3 (Win7 64 bit)

Are there any obvious reasons the cable is not good or am I doing something wrong?

Thanks!
Logged
macxxx
Sr. Member
****

Karma: +29/-1
Offline Offline

Posts: 498


« Reply #148 on: February 11, 2022, 12:08:30 PM »

I guess its based on ch340 chip so IT won't work. Check in device manager if I'm right.
Logged
bonilla
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 4


« Reply #149 on: February 12, 2022, 03:17:03 PM »

Yes, you are right. Darn, I should have read the post more carefully...

So I should get a KKL cable with a FT232R chip, right? I didn't check the chip, I just went for a generic KKL 409.1 cable.

Thanks!
Logged
Pages: 1 ... 8 9 [10] 11
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.034 seconds with 18 queries. (Pretty URLs adds 0s, 0q)