Pages: 1 ... 36 37 [38] 39 40 ... 170
Author Topic: The Volvo ME7 thread:  (Read 911653 times)
krazydbiker
Full Member
***

Karma: +4/-1
Offline Offline

Posts: 202


« Reply #555 on: July 28, 2014, 03:49:00 PM »

i believe the ross tech cable will work, look for the galleto thread somewhere, it says what to do with that cable and how to make it work

edit, found it http://nefariousmotorsports.com/forum/index.php?topic=3088.0

Logged
seppok
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 17


« Reply #556 on: July 31, 2014, 09:44:11 AM »

Fuel yes ,timing no (not to much but it's safe ,ME7.0 taking care of your engine .... smart ECU.... especially with the ignition).Try it! Wink
Had to tighten the actuator a bit to get to 0.9 bar. Works ok except there are some hiccups near 3000 rpm. It happens more often in higher gears. Is there a torque limiter or does the boost rise too quickly or what could it be? I can feel some vibration and maybe hear something and acceleration stops for a split second and then it continues. I think I have felt the same in some other car when traction control kicks in.
Logged
krazydbiker
Full Member
***

Karma: +4/-1
Offline Offline

Posts: 202


« Reply #557 on: July 31, 2014, 01:02:23 PM »

if it is overboosting, it will get that feeling of cutting back, if its severe, it will cut throttle... rumbling? like misfiring?! no, how many miles are on your spark plugs?
Logged
fredrik_a
Full Member
***

Karma: +25/-0
Offline Offline

Posts: 221


« Reply #558 on: July 31, 2014, 02:50:25 PM »

Typically the ignition coils are going bad sooner or later and this will cause the engine to behave like this when combustion pressure reaches its peak. Change them all or go cheap and buy one new coil and switch positions of it until the problems disappear given that there is just one coil that is bad.
Logged
seppok
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 17


« Reply #559 on: August 01, 2014, 07:59:57 AM »

Ok, so it could be an ignition issue. Spark plugs are new. I replaced also the coils with used ones, resistance was ok on all of them. The coil connector wires look very bad near the plug, maybe I should fix those first. Maybe it was a little worse when it was raining so that could very well be the problem. I could also try to log it in Vida.

Thanks for your help!
Logged
guitar24t
Full Member
***

Karma: +13/-0
Offline Offline

Posts: 101


« Reply #560 on: August 20, 2014, 08:21:08 PM »

Just checking in on here. What's new with anyone? Any news/new projects?
Logged
dream3R
Hero Member
*****

Karma: +18/-8
Offline Offline

Posts: 1194


« Reply #561 on: August 21, 2014, 03:38:02 AM »

Does this count?

 Grin

Logged



How to work out values from an A2L Smiley

http://nefariousmotorsports.com/forum/index.php?topic=5525.msg52371#msg52371


Starting Rev's http://nefariousmotorsports.com/forum/index.php?topic=5397.msg51169#msg51169

noobs read this before asking http://nefariousmotorsports.com/forum/index.php?topic=9014.0title=


ORGORIGINAL 05 5120 creator for Volvo
ORIGINAL Datalogger (Freeware) Author
ORGINAL finder of the 'extra' torque' limits
I don't have ME7.01 A2L I just use ID
fredrik_a
Full Member
***

Karma: +25/-0
Offline Offline

Posts: 221


« Reply #562 on: August 21, 2014, 03:58:36 AM »

Does this count?


Very cool. Not enough boost though... Smiley
Logged
dream3R
Hero Member
*****

Karma: +18/-8
Offline Offline

Posts: 1194


« Reply #563 on: August 21, 2014, 04:05:35 AM »

That was the stock boost mapping but with the 5120 mod Smiley  My god a stock S60R is slooow.

And I managed to break pu_w in that graph too so it was a little unhappy.   Roll Eyes
Logged



How to work out values from an A2L Smiley

http://nefariousmotorsports.com/forum/index.php?topic=5525.msg52371#msg52371


Starting Rev's http://nefariousmotorsports.com/forum/index.php?topic=5397.msg51169#msg51169

noobs read this before asking http://nefariousmotorsports.com/forum/index.php?topic=9014.0title=


ORGORIGINAL 05 5120 creator for Volvo
ORIGINAL Datalogger (Freeware) Author
ORGINAL finder of the 'extra' torque' limits
I don't have ME7.01 A2L I just use ID
saoron2002
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 14


« Reply #564 on: August 21, 2014, 10:07:43 AM »

That was the stock boost mapping but with the 5120 mod Smiley  My god a stock S60R is slooow.


Agree, my old D5 running decent remap keeps up with my stock R Smiley
Logged
saoron2002
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 14


« Reply #565 on: August 21, 2014, 10:15:09 AM »

Just checking in on here. What's new with anyone? Any news/new projects?

I shifted my attention to japanese cars with Denso systems, like Mitsubishi / Mazda Commonrail diesels, not much info for them around. Especially Toyota D4D, lots of them on the road and nobody remaps these. Anyone came across these and willing to invest some time ? If yes we will open new topic and I will share my experience so far with the current projects I have.
Logged
krazydbiker
Full Member
***

Karma: +4/-1
Offline Offline

Posts: 202


« Reply #566 on: August 21, 2014, 05:14:26 PM »

very good work on 5120 man!, hopefully you get to put it to work soon with a good turbo!
Logged
fredrik_a
Full Member
***

Karma: +25/-0
Offline Offline

Posts: 221


« Reply #567 on: August 22, 2014, 05:33:57 AM »

very good work on 5120 man!, hopefully you get to put it to work soon with a good turbo!

I wish I had this sorted out on my old car as the hardware could take more boost than what I could manage in my software.
I'm sure that you will push beyond 400 horses with no issues...  Grin
Logged
saoron2002
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 14


« Reply #568 on: August 22, 2014, 05:57:11 AM »

Hi to all, would someone give a clue for the nobs like me, in regards to this 5120 mod. Obviously the req boost is perfectly followed, but what's the real goal by achieving this.
Thanks in advance
Logged
fredrik_a
Full Member
***

Karma: +25/-0
Offline Offline

Posts: 221


« Reply #569 on: August 22, 2014, 06:25:34 AM »

Hi to all, would someone give a clue for the nobs like me, in regards to this 5120 mod. Obviously the req boost is perfectly followed, but what's the real goal by achieving this.
Thanks in advance

The purpose is to be able to boost more than 1.5 bar of turbo pressure, and that is not possible with stock HW and SW.

http://nefariousmotorsports.com/forum/index.php?topic=3027.0title=
Logged
Pages: 1 ... 36 37 [38] 39 40 ... 170
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.03 seconds with 17 queries. (Pretty URLs adds 0s, 0q)