slimwadey
Full Member
Karma: +0/-0
 Offline
Posts: 76
|
 |
« Reply #15 on: March 27, 2013, 02:11:14 PM »
|
|
|
well all part i need are here The pre made ECU to OBD adaptor was junk, did not fit, i assume it was for another ECU So i chopped it up made my own Ok i now have the ECU connected to my rig and my galetto cable, i have powered the ECU with a nice supply I cant seem to read anything from my ECU I have tried nefmoto and get 'failed to read test echo from ftdi device' I'm pretty sure i have the driver installed ok So i try the galetto software, after grounding pin 24 following this pic  it keeps saying bootmode inactive I have tried 20 ish times and even timed the 5 secs any pointers ? |
|
|
|
|
Logged
|
|
|
|
slimwadey
Full Member
Karma: +0/-0
Offline
Posts: 76
|
|
« Reply #16 on: March 27, 2013, 02:23:23 PM »
|
|
|
Another question Does the ECU need to be powered with a constant live on pin 3, then switch power on pin 62 to simulate ignition on/off?  |
|
|
|
|
Logged
|
|
|
|
slimwadey
Full Member
Karma: +0/-0
Offline
Posts: 76
|
|
« Reply #17 on: March 27, 2013, 03:17:02 PM »
|
|
|
|
|
|
|
|
Logged
|
|
|
|
slimwadey
Full Member
Karma: +0/-0
Offline
Posts: 76
|
|
« Reply #18 on: March 27, 2013, 03:25:27 PM »
|
|
|
just wanted to say i have checked continuity on all lines , all are fine
Should pin 3 be switched 12v and pin 63 permanent live ?
I have it wired the opposite way pin 3 permanent live and pin 63 switched live
My Galleto cable has a red light on and i'm selecting Audi Ecu's , vw/audi ME7.5 xxx 29F400BB, although i cant find any numbers on the ECU that correspond to this in any way
|
|
|
|
« Last Edit: March 27, 2013, 03:44:55 PM by slimwadey »
|
Logged
|
|
|
|
ddillenger
Moderator
Hero Member
Karma: +641/-21
Offline
Posts: 5640
|
|
« Reply #19 on: March 27, 2013, 03:26:51 PM »
|
|
|
You need to power ecu pin 21! This is true for all immobilizer equipped me7's AFAIK.
|
|
|
|
|
Logged
|
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
|
|
|
slimwadey
Full Member
Karma: +0/-0
Offline
Posts: 76
|
|
« Reply #20 on: March 27, 2013, 04:35:07 PM »
|
|
|
Ahhh !!!
Is this as well as pin 63 or instead of ?
Thanks for the help
|
|
|
|
|
Logged
|
|
|
|
ddillenger
Moderator
Hero Member
Karma: +641/-21
Offline
Posts: 5640
|
|
« Reply #21 on: March 27, 2013, 04:44:44 PM »
|
|
|
Pin 63 is left blank. Pin 62 gets 12v. Take a look at the diagram you posted. It's accurate.
|
|
|
|
|
Logged
|
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
|
|
|
slimwadey
Full Member
Karma: +0/-0
Offline
Posts: 76
|
|
« Reply #22 on: March 27, 2013, 04:51:50 PM »
|
|
|
sorry i was reading 62 and writing 63  i have been using 62 not 63 So let me get this straight Pin3 is permanent live, pin 21 is switched and pin 62 is powered too, switched with 21 or perma live ? Thanks again Steve |
|
|
|
|
Logged
|
|
|
|
ddillenger
Moderator
Hero Member
Karma: +641/-21
Offline
Posts: 5640
|
|
« Reply #23 on: March 27, 2013, 05:37:10 PM »
|
|
|
I just have them all hooked up to the 12v power source. When I power up the ecu they all get powered up. When I power it down, they all get powered down.
|
|
|
|
|
Logged
|
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
|
|
|
slimwadey
Full Member
Karma: +0/-0
Offline
Posts: 76
|
|
« Reply #24 on: March 27, 2013, 05:58:02 PM »
|
|
|
Still no luck I think its either : low power, i'm getting 12.8/12.9v not 13v + or ECU is KAPUT .... maybe due to the pad of pin 24 lifting off the PCB after me soldering a wire to it, but i re soldered onto the actual LEG of the pin and it seems fine (pic tomorrow) or maybe something to do with the cable serial number (unless this only applies to Nefmoto software) not really sure what i'm talking about on this bit so i'll shut up and read a bit more I'm sure i'm doing everything right as the cable seems to be recognised in the galetto software and Nefmoto Or its beacuse its on com port 3 Steve |
|
|
|
« Last Edit: March 27, 2013, 06:04:03 PM by slimwadey »
|
Logged
|
|
|
|
slimwadey
Full Member
Karma: +0/-0
Offline
Posts: 76
|
|
« Reply #25 on: March 28, 2013, 11:40:25 AM »
|
|
|
any ideas anyone??
|
|
|
|
|
Logged
|
|
|
|
cyril279
Full Member
Karma: +12/-2
Offline
Posts: 140
|
|
« Reply #26 on: March 29, 2013, 06:01:34 AM »
|
|
|
So let me get this straight
Pin3 is permanent live, pin 21 is switched and pin 62 is powered too, switched with 21 or perma live ?
Thanks again
Steve
pin 3 is ignition switched. All the other 12v pins see 12v all the time. putting a switch on pin3, and using that switch to initiate ecu power, made it a lot easier for me to get into bootmode. voltage shouldn't be an issue, I get bootmode using an 11.5v supply. -Cyril |
|
|
|
|
Logged
|
|
|
|
slimwadey
Full Member
Karma: +0/-0
Offline
Posts: 76
|
|
« Reply #27 on: March 31, 2013, 07:38:24 AM »
|
|
|
pin 3 is ignition switched. All the other 12v pins see 12v all the time. putting a switch on pin3, and using that switch to initiate ecu power, made it a lot easier for me to get into bootmode. voltage shouldn't be an issue, I get bootmode using an 11.5v supply.
-Cyril
Thanks Cyril, i'll give it a go |
|
|
|
|
Logged
|
|
|
|
slimwadey
Full Member
Karma: +0/-0
Offline
Posts: 76
|
|
« Reply #28 on: April 02, 2013, 01:35:56 PM »
|
|
|
After trying to get into boot mode for days now i still have had zero luck
I have Re wired my harness so it has switched 12v on No3 pin and constant 12v on 21 and 62, the kline is connected correctly and all earths are fine
My pin 24 ground switch works too , all connections to ECU have been tested with a multimeter
Still i get no response from galetto or Nefmoto
Does the USB have to talk to a certain port ?
Could i have a dead ECU ?
Any help would be appreciated
Steve
|
|
|
|
« Last Edit: April 02, 2013, 02:50:26 PM by slimwadey »
|
Logged
|
|
|
|
ddillenger
Moderator
Hero Member
Karma: +641/-21
Offline
Posts: 5640
|
|
« Reply #29 on: April 02, 2013, 02:08:43 PM »
|
|
|
You are running the galletto drivers with the software right? Did you edit the program to show the correct serial number of your cable (or edit the serial number of the cable to match the software)?
|
|
|
|
|
Logged
|
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
|
|
|
|
