Pages: 1 [2]
Author Topic: Is this dump original??? Audi A3 1.8T ARZ 06A906032AS  (Read 15543 times)
vdubnation
Turboman
Global Moderator
Sr. Member
*****

Karma: +49/-2
Offline Offline

Posts: 433


« Reply #15 on: March 26, 2013, 07:09:44 AM »

try to run it with the maf unplugged and see if it comes up
Logged
cocktailyogi
Jr. Member
**

Karma: +1/-1
Offline Offline

Posts: 42


« Reply #16 on: March 26, 2013, 12:45:51 PM »

I think there is more going on in that engine... I yust bought it and I want to fix it properly before I will go in with testing the software-mod. It throws Lamda-Error, I replaced Lambda-Sensor already. There was also a broken tube. Still Lambda error and very low MAF-values. Tomorrow I will install a new MAF-Sensor because the sensor plate looks very bad. And because of the lean mixture and resulting high EGT , no the exhaust manifault is cracked   Undecided

I will report next week, after I finished the repairs.

Yogi
Logged
vagenwerk
Full Member
***

Karma: +2/-0
Offline Offline

Posts: 182


« Reply #17 on: March 27, 2013, 04:33:29 PM »

150hp maf should read 125g-135/s, 180hp maf reads 149-155g/s  so yours is dead.
Logged
cocktailyogi
Jr. Member
**

Karma: +1/-1
Offline Offline

Posts: 42


« Reply #18 on: March 29, 2013, 05:58:37 AM »

Update....

new MAF installed, car runs better, but not perfect. MAF values are okay now, but still lambda error under load (it runs lean). Sensor is okay and idle also.

I did a pressure check with 1.5 bar on the boost system. Found 2 leaks ... intake manifold-gasket and tubing to the breake-system
There is also a pneumatic boost valve, which is leaking...

I will report, when the repairs are done... Almost an engine overhaul :-)

Yogi
Logged
cocktailyogi
Jr. Member
**

Karma: +1/-1
Offline Offline

Posts: 42


« Reply #19 on: April 06, 2013, 12:40:28 AM »

Hi, now I am making progress.

Now I fixed my leaks, replaced the boost valve and the blown exhaust manifold seals. Now car runs perfect, Lambda-values are okay, no knocking under high loads, boost control works perfect.

At this starting point I installed the modded file on ME7.5 with the 180HP TT-mapping. It runs perfect. Car drives much better and no problems under high load. no kocking and it doesn't go lean. boost is stable in MWB 115

So much power in a small car like this is perfect. :-)  Grin Grin Grin

Thanks for your help everybody!

Yogi

Logged
Patryk619
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 7


« Reply #20 on: April 04, 2018, 06:54:43 AM »

I'm sorry for reviving the thread, but I have a question regarding the file attached in this post http://nefariousmotorsports.com/forum/index.php?action=dlattach;topic=3472.0;attach=5782
Can I Flash this into my stock ARZ ecu and enjoy extra 30hp? Will it Flash and start with no problems? The author stated it worked just fine for him(the above post), I have even contacted him to ask for permision to use this but it seems he not visited the forum since December 2017.
Logged
Pages: 1 [2]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.015 seconds with 16 queries. (Pretty URLs adds 0s, 0q)