NefMoto > Vehicles > Vehicle Tech > VW 1.8t wont start after flashing incorrect file..
Pages: [1]
« previous next »
Author Topic: VW 1.8t wont start after flashing incorrect file..  (Read 9320 times)
UpstateDub
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 3
« on: August 11, 2013, 11:57:23 AM »
After flashing with an incorrect file and not having a backup of the original file, I feel like I am screwed.  The flash seemed to be successful but turned the key and got nothing.  I tried to do a scan with vcds but could not communicate with 01 Engine..  these are the auto scan results
Chassis Type: 1J - VW Golf/Bora IV
Scan: 01 02 03 08 15 16 17 19 22 29 35 36 37 39 46 47 55 56 57 75
          76
 
VIN: 9BWDE61J934028637   Mileage: 182920km/113661miles
-------------------------------------------------------------------------------
Address 03: ABS Brakes        Labels: 1C0-907-37x-ASR.lbl
   Part No: 1C0 907 379 K
   Component: ASR FRONT MK60      0103 
   Coding: 0021505
   Shop #: WSC 00000 785 00200

2 Faults Found:
00283 - ABS Wheel Speed Sensor; Front Left  (G47)
            012 - Electrical Fault in Circuit
01314 - Engine Control Module
            004 - No Signal/Communication

-------------------------------------------------------------------------------
Address 15: Airbags        Labels: 6Q0-909-605-VW5.lbl
   Part No: 1C0 909 605 F
   Component: 08 AIRBAG VW61 0202 0001 
   Coding: 12344
   Shop #: WSC 00000 

1 Fault Found:
01299 - Diagnostic Interface for Data Bus (J533)
            49-10 - No Communications - Intermittent

-------------------------------------------------------------------------------
Address 17: Instruments        Labels: 1J0-920-xx5-17.lbl
   Part No: 1J0 920 906 J
   Component: KOMBI+WEGFAHRSP VDO V07 
   Coding: 00232
   Shop #: WSC 00000 
   9BWDE61J934028637     VWZ7Z0B5808887

3 Faults Found:
01176 - Key
            07-10 - Signal too Low - Intermittent
01177 - Engine Control Unit
            64-10 - Not Currently Testable - Intermittent
01314 - Engine Control Module
            49-00 - No Communications

-------------------------------------------------------------------------------
Address 19: CAN Gateway        Labels: 6N0-909-901-19.lbl
   Part No: 6N0 909 901
   Component: Gateway K<->CAN    0001 
   Coding: 00006
   Shop #: WSC 00000 

1 Fault Found:
01314 - Engine Control Module
            49-00 - No Communications

-------------------------------------------------------------------------------
Address 46: Central Conv.        Labels: 1C0-959-799.lbl
   Part No: 1C0 959 799 C
   Component: 8B Komfortgerát HLO 0003 
   Coding: 00065
   Shop #: WSC 00000 

   Part No: 1C1959801A
   Component: 8B Tõrsteuer.FS KLO 0002 

   Part No: 1C1959802A
   Component: 8B Tõrsteuer.BF KLO 0002 

2 Faults Found:
01299 - Diagnostic Interface for Data Bus (J533)
            49-10 - No Communications - Intermittent
00928 - Locking Module for Central Locking; Front Driver Side (F220)
            27-00 - Implausible Signal

End   ---------------------------------------------------------------------
Logged
UpstateDub
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 3
« Reply #1 on: August 11, 2013, 12:00:10 PM »
One thing I did notice is that upon turning the key to postion 2, I would usually notice the cel light and epc light on, after the flash, these two do not come on anymore.  This happened once before after I dropped in a new motor where I had to jump relay's under the hood in order for those two lights to come on, this time around, it's not working for me..
Logged
matchew
Hero Member
*****

Karma: +47/-22
Offline Offline

Posts: 503
« Reply #2 on: August 11, 2013, 12:22:16 PM »
Bricked
Logged
UpstateDub
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 3
« Reply #3 on: August 11, 2013, 12:43:09 PM »
Quote from: matchew on August 11, 2013, 12:22:16 PM
Bricked
yeah I figured that much. Just wish there was a way to get ecu into bootmode without having to do bench work.
Logged
99pwr
Full Member
***

Karma: +15/-0
Offline Offline

Posts: 85
« Reply #4 on: August 11, 2013, 03:21:51 PM »
Try to write this file, I think it is original file for your car http://nefariousmotorsports.com/forum/index.php?topic=3438.0
Logged
ddillenger
Hero Member
*****

Karma: +641/-21
Offline Offline

Posts: 5640
« Reply #5 on: August 11, 2013, 03:35:30 PM »
You can bootmode in car. Just takes two people.
Logged
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM
aysix
Jr. Member
**

Karma: +12/-0
Offline Offline

Posts: 37
« Reply #6 on: August 20, 2013, 07:01:51 PM »
Quote from: ddillenger on August 11, 2013, 03:35:30 PM
You can bootmode in car. Just takes two people.

A little late on this but you can do it by your self if you keep the key on the acc position and power up the ecu by attaching positive terminal on the battery.
Logged
Silly Rabbit 6 speed A6
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 29, 2024, 03:44:46 PM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.019 seconds with 16 queries. (Pretty URLs adds 0s, 0q)