Pages: [1]
Author Topic: 2000 s4 Boost surge, throttle cut  (Read 7675 times)
heff
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 9


« on: November 04, 2013, 03:39:15 PM »

Car is a 2000 s4, ko4 6 spd. Rs4 maf, siemens 60# injector, srm intercooler, bosch 044 pump, eurodyne/tapp software

The last few months the car is having very poor part throttle condition, As well seems to have less power at wot throttle as well. Car has misfires at idle but believe this to be from siemens 60 # injectors. While driving and at w.o.t the car has ZERO misfires. Plugs are ngk and gapped at .25, have new coil packs and i.c.ms.

I Took some logs last night and will upload one at w.o.t that i start real low in rpm ( on side note hammering throttle early in gear vs later seemed to always have lower boost peak) and the second log shows my part throttle issue in regards to boost fluctuation or surging. I can see i am getting throttle cut., Not knowing what variable is causing all of these issues to react its hard to pinpoint...Hoping some of you that are familiar with tuning and reading logs can chime in with suggestions, if you need a log with different parametres i can produce them as well, thanks for any help!

heres w.o.t log..

heres part throttle log http://i822.photobucket.com/albums/zz142/sasks4/3boostsurge_zpsac9bc38d.pnghttp://i822.photobucket.com/albums/zz142/sasks4/wotthrottlecut_zpsae2e5bbe.png
Logged
heff
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 9


« Reply #1 on: November 04, 2013, 04:04:14 PM »

Sorry here is the part throttle log..http://i822.photobucket.com/albums/zz142/sasks4/3boostsurge_zpsac9bc38d.png

the one in first post is w.o.t. run.
Logged
Krayzie
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 3


« Reply #2 on: December 23, 2013, 09:09:23 PM »

Hi,from the logs,it seems like your boost deviation is to high...actual vs specified. That's why you getting throttle cut,the ecu Is trying to keep your boost levels in check. Check all your vacuum piping,the wastegate and your n75 valve. Hope you come right.
Logged
Rocket
Newbie
*

Karma: +1/-0
Offline Offline

Posts: 15


« Reply #3 on: February 19, 2014, 12:02:19 PM »

You can adjust the wastegates with the 10mm bolts 2-3 turns toward the end of the rods (unscrew).
Logged
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12233


WWW
« Reply #4 on: February 19, 2014, 12:03:30 PM »

waste gate lines are torn or your n75 is dead
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
vdubnation
Turboman
Global Moderator
Sr. Member
*****

Karma: +49/-2
Offline Offline

Posts: 433


« Reply #5 on: February 19, 2014, 02:05:38 PM »

^^^^^^^^^^^^^^^^^^^^^^^^
Seen this so many times just resolved this issue on someones car who was battling this for 18 months.
Logged
Lost
Hero Member
*****

Karma: +21/-14
Offline Offline

Posts: 556


« Reply #6 on: February 19, 2014, 02:53:49 PM »

^^^^^^^^^^^^^^^^^^^^^^^^
Seen this so many times just resolved this issue on someones car who was battling this for 18 months.

And solution was?
Logged
ddillenger
Hero Member
*****

Karma: +638/-21
Offline Offline

Posts: 5640


« Reply #7 on: February 19, 2014, 03:17:43 PM »

Torn wastegate lines.
Logged

Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM
userpike
Hero Member
*****

Karma: +22/-1
Offline Offline

Posts: 763


« Reply #8 on: February 20, 2014, 08:20:52 AM »

I had an issue similar to this on my 1.8t, but without so much throttle cut, because of a pcv hose clamp I missed to tighten for a catch can...I assume a crack would give the same symptoms.
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.02 seconds with 17 queries. (Pretty URLs adds 0s, 0q)