sqitis
Full Member
Karma: +2/-0
 Offline
Posts: 58
|
 |
« on: April 02, 2011, 01:59:30 PM »
|
|
|
all the other buttons are grayed out said that layout file is needed. Where do I get this xml file needed for the layout?
Thanks!
|
|
|
|
|
Logged
|
|
|
|
sqitis
Full Member
Karma: +2/-0
Offline
Posts: 58
|
|
« Reply #1 on: April 02, 2011, 02:02:21 PM »
|
|
|
Ok it says specified layout is not correct. Not real sure what that means.
|
|
|
|
|
Logged
|
|
|
|
|
phila_dot
|
|
« Reply #2 on: April 02, 2011, 03:18:20 PM »
|
|
|
What ECU? It sounds like you figured out to browse and select a layout. Which one did you select?
|
|
|
|
|
Logged
|
|
|
|
sqitis
Full Member
Karma: +2/-0
Offline
Posts: 58
|
|
« Reply #3 on: April 02, 2011, 03:20:28 PM »
|
|
|
It's an 00 S4 A-box 551A. Ok I used the F200 and now it validates but the other buttons are still greyed out.
|
|
|
|
|
Logged
|
|
|
|
|
phila_dot
|
|
« Reply #4 on: April 02, 2011, 03:23:09 PM »
|
|
|
Try 29F800
|
|
|
|
|
Logged
|
|
|
|
sqitis
Full Member
Karma: +2/-0
Offline
Posts: 58
|
|
« Reply #5 on: April 02, 2011, 03:34:44 PM »
|
|
|
Ok that worked! How do upload a flash .bin file?
|
|
|
|
|
Logged
|
|
|
|
|
phila_dot
|
|
« Reply #6 on: April 02, 2011, 05:05:38 PM »
|
|
|
Are you on a bench or in the car? First, you going to want to read flash to download and backup your binary file. Then, if you have a tuned file to flash you will want to write flash. If you are flashing in the car, ensure that you have enough power. I either hook up jumper cables to my other car, or, if I am at the garage, I hook up a charger. Also, if you are flashing a tuned file, make sure your checksums are corrected before flashing. I use setzi's ME7check everytime before flashing to make sure.
|
|
|
|
|
Logged
|
|
|
|
sqitis
Full Member
Karma: +2/-0
Offline
Posts: 58
|
|
« Reply #7 on: April 02, 2011, 07:28:08 PM »
|
|
|
Ok so what is wrong with this file? Tried to load it and the car would not start but said flash completed successfully.
TIA!
|
|
|
|
|
Logged
|
|
|
|
Giannis
Full Member
Karma: +11/-1
Offline
Posts: 176
|
|
« Reply #8 on: April 14, 2011, 12:33:08 PM »
|
|
|
welcome to the club my friend i'm trying to find out the same...  |
|
|
|
|
Logged
|
|
|
|
carlossus
Sr. Member
Karma: +38/-0
Offline
Posts: 394
Leon Curpa Stg1+
|
 |
« Reply #9 on: April 18, 2011, 03:28:10 PM »
|
|
|
For the record it is entirely possible to have a BIN file full of garbage that has been checksum corrected.
This is a pain because it'll flash fine but then ODB2 flashing wont work.
It would be nice if only known BIN files were posted otherwise the forum could get flooded with bricked ECU victims.
|
|
|
|
« Last Edit: April 18, 2011, 03:32:48 PM by carlossus »
|
Logged
|
|
|
|
Rated S
Newbie
Karma: +3/-0
Offline
Posts: 11
|
|
« Reply #10 on: April 28, 2011, 01:35:51 PM »
|
|
|
Should ban the uploading of .bin files in the forum(sans legitimate files), and perhaps make another section explicitly for posting 'what's wrong with this .bin' threads and allowing uploads in them, stating to not openly use these on their cars.
|
|
|
|
|
Logged
|
socals4.com/repair - ecux/vagcom/diy
|
|
|
|
