Dev Blog
Forum
Wiki
About
NefMoto
>
Technical
>
Diagnostics
>
Can't soft code out DCTs! M-box on euro c-box car
Pages: [
1
]
« previous
next »
Author
Topic: Can't soft code out DCTs! M-box on euro c-box car (Read 10880 times)
smurfbus
Jr. Member
Karma: +0/-1
Offline
Posts: 38
Can't soft code out DCTs! M-box on euro c-box car
« on: January 26, 2014, 08:02:51 AM »
I have tried different vardefs and different login codes (13737 and 11463) on vcds but nada. I can only change 06611 to 06711 but not the needed 05211 or 10211 as my car has no ASR/ESP and no CAN either?
Is there something I can do or forgot to do? I have FF'ed the ESKONF bytes 1,3,6 and 7
Address 01: Engine Labels: 078-907-551-AZA.lbl
Part No: 8D0 907 551 M
Component: 2.7l V6/5VT G 0001
Coding: 06611
Shop #: WSC 87119
VCID: 346A1131043DC0BE40B-5102
3 Faults Found:
17881 - EVAP Leak Detection Pump
P1473 - 35-00 - Open Circuit
17931 - Crash Signal from Airbag Controller
P1523 - 35-00 - Implausible Signal
18014 - Rough Road/Engine Torque Signal from ABS
P1606 - 35-00 - Electrical Malfunction
Readiness: 0000 0000
Logged
armageddon
Sr. Member
Karma: +20/-3
Offline
Posts: 348
Re: Can't soft code out DCTs! M-box on euro c-box car
« Reply #1 on: January 28, 2014, 04:10:30 PM »
To remove EVAP
http://s4wiki.com/wiki/Tuning
To remove P1523 go to 0x10735 and change 13 to 00
To remove P1606 go to 0x10730 and change 13 to 00
Logged
smurfbus
Jr. Member
Karma: +0/-1
Offline
Posts: 38
Re: Can't soft code out DCTs! M-box on euro c-box car
« Reply #2 on: January 31, 2014, 02:47:06 AM »
Thanks
Still have evap P1473 DTC though (LDP circuit open circuit). Done these below as per s4wiki:
Evaporation
CDTES - Eurobyte - LDP Diagnosis
CDLDP - Eurobyte - EVAP diagnosis
CLATEVE - EVAP plug
CLALDPE - LDP plug
Logged
ddillenger
Hero Member
Karma: +641/-21
Offline
Posts: 5640
Re: Can't soft code out DCTs! M-box on euro c-box car
« Reply #3 on: January 31, 2014, 10:11:58 AM »
Change 10C77 from E3 to EF.
Logged
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
smurfbus
Jr. Member
Karma: +0/-1
Offline
Posts: 38
Re: Can't soft code out DCTs! M-box on euro c-box car
« Reply #4 on: February 03, 2014, 07:25:32 AM »
That did not help?
Logged
ddillenger
Hero Member
Karma: +641/-21
Offline
Posts: 5640
Re: Can't soft code out DCTs! M-box on euro c-box car
« Reply #5 on: February 03, 2014, 07:47:19 AM »
Post the file that it "didn't help" please.
Logged
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
smurfbus
Jr. Member
Karma: +0/-1
Offline
Posts: 38
Re: Can't soft code out DCTs! M-box on euro c-box car
« Reply #6 on: February 04, 2014, 10:51:19 PM »
I checked the bin and the change I set/saved was not there? Sometimes tunerpro does not really save the saved values so for now on I will double check the values are saved properly. I did not check the code yet but hopefully its gone now.
Logged
ddillenger
Hero Member
Karma: +641/-21
Offline
Posts: 5640
Re: Can't soft code out DCTs! M-box on euro c-box car
« Reply #7 on: February 05, 2014, 12:07:59 AM »
I am 100 percent sure that the change listed will remove LDP circuit diagnosis.
Logged
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
smurfbus
Jr. Member
Karma: +0/-1
Offline
Posts: 38
Re: Can't soft code out DCTs! M-box on euro c-box car
« Reply #8 on: February 23, 2014, 06:59:40 AM »
Just for follow up, you're 100% correct.
Logged
andysterling
Newbie
Karma: +0/-0
Offline
Posts: 1
Re: Can't soft code out DCTs! M-box on euro c-box car
« Reply #9 on: January 21, 2021, 03:36:27 PM »
Not sure where start and apologies for resurecting this thread, but i've recently bought an 01.5 S4 B5 avant and have followed these guides, i now have a stage1 tune with disabled evap, absolutely cracking job from you guys
Logged
Pages: [
1
]
Print
« previous
next »
Jump to:
Please select a destination:
-----------------------------
General
-----------------------------
=> Introductions
=> General Discussion
-----------------------------
Noob Zone
-----------------------------
=> Noob Questions
=> Noob Guides and FAQs
-----------------------------
Technical
-----------------------------
=> NefMoto Software
=> Tuning
===> Documents & Helpers & How To's
===> Community Projects
=> Diagnostics
=> Flashing and Chipping
=> Cluster and Immobilizer
===> ECU EEPROM images
===> Original Cluster dumps
===> Original Cluster dump requests
=> Data Logging
=> Reverse Engineering
=> Communication Protocols
-----------------------------
ECU Files
-----------------------------
=> ECU Definition Files
===> ECU Definition File Requests
=> Original ECU Files
===> Original ECU File Requests
=> Checksum Update Requests
-----------------------------
Vehicles
-----------------------------
=> Vehicle Tech
=> Project Cars
-----------------------------
Regional
-----------------------------
=> Canadian Regional Discussion
=> US Regional Discussion
-----------------------------
Classifieds
-----------------------------
=> For Sale
=> Wanted
=> Services
-----------------------------
Miscellaneous
-----------------------------
=> Off Topic
=> Forum Tech Support
=> Bizarro Messages Posted by Bots and Spammers
Navigation
Home
Help
Login
Register
Personal Tools
November 23, 2024, 12:49:12 PM
Welcome,
Guest
. Please
login
or
register
.
Did you miss your
activation email?
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
Search
Advanced Search
Loading...
