Pages: [1]
Author Topic: Can't soft code out DCTs! M-box on euro c-box car  (Read 10232 times)
smurfbus
Jr. Member
**

Karma: +0/-1
Offline Offline

Posts: 38


« on: January 26, 2014, 08:02:51 AM »

I have tried different vardefs and different login codes (13737 and 11463) on vcds but nada. I can only change 06611 to 06711 but not the needed 05211 or 10211 as my car has no ASR/ESP and no CAN either?

Is there something I can do or forgot to do? I have FF'ed the ESKONF bytes 1,3,6 and 7

Address 01: Engine        Labels: 078-907-551-AZA.lbl
   Part No: 8D0 907 551 M
   Component: 2.7l V6/5VT     G   0001 
   Coding: 06611
   Shop #: WSC 87119 
   VCID: 346A1131043DC0BE40B-5102

3 Faults Found:
17881 - EVAP Leak Detection Pump
            P1473 - 35-00 - Open Circuit
17931 - Crash Signal from Airbag Controller
            P1523 - 35-00 - Implausible Signal
18014 - Rough Road/Engine Torque Signal from ABS
            P1606 - 35-00 - Electrical Malfunction
Readiness: 0000 0000
Logged
armageddon
Sr. Member
****

Karma: +20/-3
Offline Offline

Posts: 348


« Reply #1 on: January 28, 2014, 04:10:30 PM »

To remove EVAP http://s4wiki.com/wiki/Tuning

To remove P1523 go to 0x10735 and change 13 to 00

To remove P1606 go to 0x10730 and change 13 to 00
Logged
smurfbus
Jr. Member
**

Karma: +0/-1
Offline Offline

Posts: 38


« Reply #2 on: January 31, 2014, 02:47:06 AM »

Thanks

Still have evap P1473 DTC though (LDP circuit open circuit). Done these below as per s4wiki:

Evaporation

CDTES - Eurobyte - LDP Diagnosis
CDLDP - Eurobyte - EVAP diagnosis
CLATEVE - EVAP plug
CLALDPE - LDP plug
Logged
ddillenger
Hero Member
*****

Karma: +637/-21
Offline Offline

Posts: 5640


« Reply #3 on: January 31, 2014, 10:11:58 AM »

Change 10C77 from E3 to EF.
Logged

Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM
smurfbus
Jr. Member
**

Karma: +0/-1
Offline Offline

Posts: 38


« Reply #4 on: February 03, 2014, 07:25:32 AM »

That did not help?
Logged
ddillenger
Hero Member
*****

Karma: +637/-21
Offline Offline

Posts: 5640


« Reply #5 on: February 03, 2014, 07:47:19 AM »

Post the file that it "didn't help" please.
Logged

Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM
smurfbus
Jr. Member
**

Karma: +0/-1
Offline Offline

Posts: 38


« Reply #6 on: February 04, 2014, 10:51:19 PM »

I checked the bin and the change I set/saved was not there? Sometimes tunerpro does not really save the saved values so for now on I will double check the values are saved properly. I did not check the code yet but hopefully its gone now.
Logged
ddillenger
Hero Member
*****

Karma: +637/-21
Offline Offline

Posts: 5640


« Reply #7 on: February 05, 2014, 12:07:59 AM »

I am 100 percent sure that the change listed will remove LDP circuit diagnosis.
Logged

Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM
smurfbus
Jr. Member
**

Karma: +0/-1
Offline Offline

Posts: 38


« Reply #8 on: February 23, 2014, 06:59:40 AM »

Just for follow up, you're 100% correct.
Logged
andysterling
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 1


« Reply #9 on: January 21, 2021, 03:36:27 PM »

Not sure where start and apologies for resurecting this thread, but i've recently bought an 01.5 S4 B5 avant and have followed these guides, i now have a stage1  tune with disabled evap, absolutely cracking job from you guys Cheesy

Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.54 seconds with 16 queries. (Pretty URLs adds 0s, 0q)