Pages: [1]
Author Topic: I cant read my ECU!?  (Read 8044 times)
stahlg
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 7



« on: February 02, 2014, 03:52:36 AM »

Hey Friends!

I have a connection with NefMoto and read ECU info no problem. Using a original HEX-USB Interface with bench harness cable.

I cant read the flash from the ECU. Every time the Message "Reading ECU flash memory failed" is comming. I dont know why?

Using several baudrates without any result. ECU is from a S3 1.8T BAM Engine. (ML906032A  1.8l R4/5VT 0002)

The Memorylayout i have used is the: 29F800BB that must be right!?

ich weiß nicht weiter. please help.
Logged
stahlg
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 7



« Reply #1 on: February 02, 2014, 03:53:09 AM »

Disabling Windows sleep mode.
Reading ECU flash memory.
ECU reports programming session preconditions have been met.
Negotiating communication timings.
Successfully changed to new communication timings.
Requesting security access.
ECU reports that security access request was rejected.
Starting diagnostic session.
Disconnecting because no response was received for the Tester Present message.
Disconnected
Reading ECU flash memory failed.
100% complete.
Restoring Windows sleep mode.
Logged
_nameless
Hero Member
*****

Karma: +320/-445
Offline Offline

Posts: 2654



« Reply #2 on: February 02, 2014, 03:48:12 PM »

Disabling Windows sleep mode.
Reading ECU flash memory.
ECU reports programming session preconditions have been met.
Negotiating communication timings.
Successfully changed to new communication timings.
Requesting security access.
ECU reports that security access request was rejected.
Starting diagnostic session.
Disconnecting because no response was received for the Tester Present message.
Disconnected
Reading ECU flash memory failed.
100% complete.
Restoring Windows sleep mode.
do your self a favor and buy this. no memory selection or connection speed. also has boot mode recovery. For the price you cat get any better  http://www.ebay.com/itm/SMPS-MPPS-K-CAN-V13-Chip-Tuning-Power-Auto-ECU-Tuning-Car-Remap-OBD2-OBD-Cable-1-/181289298628?pt=Motors_Automotive_Tools&hash=item2a35af2ac4&vxp=mtr
Logged

If you are in the market for a tune and would like the ease of downloading and flashing a dyno tested tune for a fair price check out https://instatune.sellfy.store/
stahlg
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 7



« Reply #3 on: February 04, 2014, 09:30:59 AM »

i have a MPPS V12 cable. that works perfect. but not in combination with NefMoto??

Thats not the Question man;) I need help about the Problem with ECU reading Problems in Nefmoto
Logged
jogtx16v
Full Member
***

Karma: +6/-1
Offline Offline

Posts: 139



« Reply #4 on: February 04, 2014, 09:58:25 AM »

I also tried to read/flash with nefmoto on the bench, with kpw2000 protocol and I have the same problem ''ECU reports that security access request was rejected. '' and ''Reading ECU flash memory failed'' on 032DL 1.8t ecu

I think nefmoto are better for read/flash ecu in car. not sure about this thing. if anybody can confirm ?

In the bench I read/flash with galletto in boot mode with blue KKL ftdi cable.
I have adapted the serial # of the FTDI chip to work with galletto software.

sorry for my english





« Last Edit: February 04, 2014, 10:02:07 AM by jogtx16v » Logged
_nameless
Hero Member
*****

Karma: +320/-445
Offline Offline

Posts: 2654



« Reply #5 on: February 06, 2014, 08:44:21 PM »

why do you need nefmoto for a read when you have other software that will work just fine?
Logged

If you are in the market for a tune and would like the ease of downloading and flashing a dyno tested tune for a fair price check out https://instatune.sellfy.store/
stahlg
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 7



« Reply #6 on: February 10, 2014, 11:52:04 AM »

because that nefmoto forum is here Cool

and I want to know why nefmoto not WORK?
Logged
ddillenger
Hero Member
*****

Karma: +637/-21
Offline Offline

Posts: 5640


« Reply #7 on: February 10, 2014, 11:57:32 AM »

Just like the narrowband TT's, nefmoto rarely works. Tony's not around much for support either I'm afraid.
Logged

Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.017 seconds with 17 queries. (Pretty URLs adds 0s, 0q)