Pages: 1 ... 4 5 [6] 7 8
Author Topic: FKKVS Fixer  (Read 66295 times)
HelperD
Full Member
***

Karma: +25/-6
Offline Offline

Posts: 112


« Reply #75 on: September 14, 2017, 08:58:21 PM »

Great share
« Last Edit: January 07, 2018, 04:52:23 PM by HelperD » Logged
KasperH
Hero Member
*****

Karma: +24/-8
Offline Offline

Posts: 632


« Reply #76 on: September 15, 2017, 07:29:41 AM »

Then make a log configuration that logs only the variables mentioned in the quote I posted before Smiley
Logged
HelperD
Full Member
***

Karma: +25/-6
Offline Offline

Posts: 112


« Reply #77 on: September 15, 2017, 08:00:51 PM »

Smiley
« Last Edit: January 07, 2018, 04:52:05 PM by HelperD » Logged
KasperH
Hero Member
*****

Karma: +24/-8
Offline Offline

Posts: 632


« Reply #78 on: September 16, 2017, 03:58:49 AM »

Do it a bank at a time, but I'm not sure the software can figure it out when there's bank designation in the data (1&2)
Also I seem to remember that all 2.7TT was narrowband?
Logged
pedrosousa
Full Member
***

Karma: +3/-0
Offline Offline

Posts: 75


« Reply #79 on: September 23, 2017, 12:28:12 AM »

Hi,

I need help with something that's happening.

I use NOLRA=7
I do the logs with me7 and the correct variables
I'm using the latest version of the fixer

Last year I used this program and worked great, recently I'm getting this kind of output and can't understand what I'm doing wrong.
Logged
6L20vt
Full Member
***

Karma: +2/-0
Offline Offline

Posts: 152


« Reply #80 on: December 05, 2017, 12:42:52 AM »

The process is :
I copy my current fkkvs, charge the log, and must give me the recalculated fkkvs is not it?

thanks
Logged
.
Jr. Member
**

Karma: +0/-3
Offline Offline

Posts: 29


« Reply #81 on: December 06, 2017, 08:18:06 PM »

Should I enter the new fkkvs in each pass? or charge the same fkkvs and I'm going through the different logs?
Logged
Hollywood
Full Member
***

Karma: +6/-1
Offline Offline

Posts: 60


« Reply #82 on: December 14, 2017, 07:28:03 PM »

Should I enter the new fkkvs in each pass? or charge the same fkkvs and I'm going through the different logs?

Enter your current FKKVS, log, run fixer. Copy output FKKVS to your tune, flash. Enter the NEW FKKVS that you just copied into your tune and fresh log into fixer, generate even more better new FKKVS.... repeat until the changes become minimal.

So yes, you'll input the newest version of you FKKVS every time, not the base file with all 1's
Logged
6L20vt
Full Member
***

Karma: +2/-0
Offline Offline

Posts: 152


« Reply #83 on: December 15, 2017, 11:51:26 PM »

hello again, however much I try to improve using fkkvs fixer, I always get a worse result, exactly how the factor of that map works, above the higher value I enrich the mix? I have tried increasing the map 0.3% the map to observe the reaction, but I have only managed to make it worse and make it more unstable. I want to make more stable to 1 in idle and cruise. could you help me?
Logged
_nameless
Hero Member
*****

Karma: +320/-445
Offline Offline

Posts: 2654



« Reply #84 on: December 22, 2017, 08:43:49 AM »

hello again, however much I try to improve using fkkvs fixer, I always get a worse result, exactly how the factor of that map works, above the higher value I enrich the mix? I have tried increasing the map 0.3% the map to observe the reaction, but I have only managed to make it worse and make it more unstable. I want to make more stable to 1 in idle and cruise. could you help me?
are you sure tvub are krkte are right? lambda control within 10%?
Logged

If you are in the market for a tune and would like the ease of downloading and flashing a dyno tested tune for a fair price check out https://instatune.sellfy.store/
6L20vt
Full Member
***

Karma: +2/-0
Offline Offline

Posts: 152


« Reply #85 on: December 22, 2017, 08:55:59 AM »

are you sure tvub are krkte are right? lambda control within 10%?


yes, krkte,tuvb is from s3 file
Logged
golfputtputt
Sr. Member
****

Karma: +6/-4
Offline Offline

Posts: 367


« Reply #86 on: January 02, 2018, 02:04:30 PM »

is "099 -> switch basic settings ON -> LR off" in vcds the same as setting NOLRA=7?
Logged
sonique
Sr. Member
****

Karma: +24/-12
Offline Offline

Posts: 282


« Reply #87 on: January 02, 2018, 02:13:08 PM »

is "099 -> switch basic settings ON -> LR off" in vcds the same as setting NOLRA=7?
no
nolra switch off adaptation 32 channel
lambda control not
Logged
golfputtputt
Sr. Member
****

Karma: +6/-4
Offline Offline

Posts: 367


« Reply #88 on: January 02, 2018, 02:32:30 PM »

found NOLRA scalar in xdf, is there no easy way to change its value without reuploading a new .bin every time I want to log for this FKKVS fixer? like in vcds or something?
« Last Edit: January 02, 2018, 03:02:44 PM by golfputtputt » Logged
KasperH
Hero Member
*****

Karma: +24/-8
Offline Offline

Posts: 632


« Reply #89 on: January 03, 2018, 06:06:46 PM »

found NOLRA scalar in xdf, is there no easy way to change its value without reuploading a new .bin every time I want to log for this FKKVS fixer? like in vcds or something?

Who gave you the idea this would be easy?
This is what I've done, I have had some days where I would write to the ECU 30 times.
Even the LDRPID feed forward takes a minimum of 10 writes/logs.
FKKVS fixer could be done in 2 writes and 1 log.

But I remember some mention of using the unused channel in investing to change a scalar value.
But can't remember who, where or if it worked?
Logged
Pages: 1 ... 4 5 [6] 7 8
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.039 seconds with 16 queries. (Pretty URLs adds 0s, 0q)