nezzo
Newbie
Karma: +1/-0
 Offline
Posts: 21
|
 |
« Reply #525 on: March 25, 2016, 03:57:46 PM »
|
|
|
And this is how it works 1/3 throttle while stationary https://www.youtube.com/watch?v=wpIyiikFW7kBut NLS doesn't work, I tried to set the throttle position to 0 but it doesn't change anything. Launch control disenagages at 3km/h so I guess it's not that, and the current engine revs are also properly detected otherwise LC wouldn't work as well. |
|
|
|
|
Logged
|
|
|
|
nezzo
Newbie
Karma: +1/-0
Offline
Posts: 21
|
|
« Reply #526 on: March 28, 2016, 11:20:01 AM »
|
|
|
I finally managed to get the NLS working, stupid D-box has inverse brake signal, so in ECUs mind I was constantly braking, thats why it didn't work.
I've attached how it looks in the logs from a rolling start from 2nd -> 3rd -> 4th.
|
|
|
|
« Last Edit: March 28, 2016, 11:24:59 AM by nezzo »
|
Logged
|
|
|
|
nezzo
Newbie
Karma: +1/-0
Offline
Posts: 21
|
|
« Reply #527 on: March 29, 2016, 03:41:11 PM »
|
|
|
first losses, scratch one oxygen sensor at bank2  |
|
|
|
|
Logged
|
|
|
|
nezzo
Newbie
Karma: +1/-0
Offline
Posts: 21
|
|
« Reply #528 on: April 11, 2016, 02:42:17 AM »
|
|
|
more severe losses: rear diff (torsen swapped from a V8) has disintegrated during a launch (from standstill) a few meters after clutch release.
|
|
|
|
|
Logged
|
|
|
|
|
gt-innovation
|
|
« Reply #529 on: April 11, 2016, 02:58:52 AM »
|
|
|
more severe losses: rear diff (torsen swapped from a V8) has disintegrated during a launch (from standstill) a few meters after clutch release.
Running my car almost 3 years now with als nls..after 2 years lamabda was damaged but not severly..Turbocharger though is getting a sock so i assume sooner or later i will change the second one  |
|
|
|
« Last Edit: April 11, 2016, 01:01:28 PM by gt-innovation »
|
Logged
|
|
|
|
|
armageddon
|
|
« Reply #530 on: April 11, 2016, 10:20:59 AM »
|
|
|
more severe losses: rear diff (torsen swapped from a V8) has disintegrated during a launch (from standstill) a few meters after clutch release.
EDL killed it |
|
|
|
|
Logged
|
|
|
|
|
|
|
armageddon
|
|
« Reply #532 on: April 12, 2016, 02:38:00 AM »
|
|
|
There's two tyoes of v8 torsem diff, that is the weaker
try getting one of these, or a quaife
|
|
|
|
|
Logged
|
|
|
|
pOwy
Full Member
Karma: +0/-0
Offline
Posts: 52
|
|
« Reply #533 on: May 01, 2016, 08:50:21 AM »
|
|
|
I made my file with the php, launch control works fine, but i think it cutting fuel as well. nls does not work. i have read the 36pages from this topic and i dont know why.
how can i change the variables for lc/nls? i need an another def file to do this?
here is my ori and the mod file, if someone have some time please check:)
thanks
|
|
|
|
|
Logged
|
|
|
|
TijnCU
Hero Member
Karma: +60/-4
Offline
Posts: 690
flying brick
|
|
« Reply #534 on: May 01, 2016, 10:58:08 AM »
|
|
|
I am going to try to make NLS be more like a real ALS that works on up-shifts and down-shifts, therefore it would be good to have a simple on/off switch.
I enjoyed your videos :-) You would have to rewrite the function to do this, but for sure it is possible to replace the routine startup conditions (temp+pedal) with a 5v or 12v switch that you connect to any unused I/O port of the ecu. For example secondary lambda. That is, if you can write functions in assembly. (I still cant) |
|
|
|
|
Logged
|
|
|
|
kaiten_ricardo
Newbie
Karma: +0/-0
Offline
Posts: 1
|
|
« Reply #535 on: May 25, 2016, 01:39:31 AM »
|
|
|
i am trying to implement this code in a 1.8t file but my file is smaller so the new function is located earlier, i am starting to look at assembly language but can't sort this yet.
i've putted the code in 7ff67, how does this translate in assembly?
is there a assembly converter for me7?
|
|
|
|
|
Logged
|
|
|
|
doubas
Newbie
Karma: +0/-0
Offline
Posts: 13
|
|
« Reply #536 on: May 26, 2016, 03:23:19 PM »
|
|
|
How to tell where exactly to implement the NLS/AL code in the bin? I have zero experience in programming.. thx
|
|
|
|
|
Logged
|
|
|
|
J.Laborde
Full Member
Karma: +57/-29
Offline
Posts: 82
Tuner and Software Developer
|
|
« Reply #537 on: May 26, 2016, 06:50:03 PM »
|
|
|
How to tell where exactly to implement the NLS/AL code in the bin? I have zero experience in programming.. thx
Inbox me I will help guide you through the steps. Regards |
|
|
|
|
Logged
|
I am here to learn and help others learn. He's a maniac.......MAAAAAANIIIAC
|
|
|
nezzo
Newbie
Karma: +1/-0
Offline
Posts: 21
|
|
« Reply #538 on: May 27, 2016, 02:09:14 AM »
|
|
|
first losses, scratch one oxygen sensor at bank2 I retract what I said before about everything working. I'm running a 3rd set of oxygen sensors since I installed ALS/LC. |
|
|
|
|
Logged
|
|
|
|
vara82
Full Member
Karma: +2/-0
Offline
Posts: 64
|
|
« Reply #539 on: May 31, 2016, 09:08:08 AM »
|
|
|
Sorry for my question... I ran launch.exe over my 1ML906032A file and everything seems fine. No errors there. Checksum corrected and flashed to my ECU. But nothing works  No AL, no NLS Can anyone take a look to my file and can tell me where the fault is?! Much thanks. Best regards, Flo |
|
|
|
|
Logged
|
|
|
|
|
