Pages: [1] 2
Author Topic: Problems reading from 99 A4 1.8L R4 5VT 4B0906018 0004  (Read 18016 times)
LHN86
Full Member
***

Karma: +5/-1
Offline Offline

Posts: 63


Engineer


« on: May 25, 2014, 01:55:48 PM »

Hi there!

I have problems reading the flash memory from the ecu in topic. I am using an original ross-tech cable with VCP drivers, the VCP drivers making the connection session work good with minor issues with the standard ross-tech drivers. But the flash memory reading is still not possible. If i can read the log right, the read sessions cannot come through by some unsupported security access. I have also noticed that it using kwp2000 session in fast int. due to 1281 in slow int. with the ecu data promted, and though the ecu is an older type, should it be an early me7.

Thanks for any help that you maybe havo to solve this problem.

Ha have printed the session log in slow and fast int. with ecu memory read atempt and ecu info read.


124800 Baud Slow int.:

Switching to KWP2000 session.
Validated FTDI device is in dumb mode.
Disconnected
Connecting...
Starting slow init connection.
Connecting to address 0x01.
Slow init succeeded.
Switching to KWP1281 session.
KWP1281 connect info: 4B0906018   1.8L R4 5VT         0004

124800 Baud Fast int.:

Validated FTDI device is in dumb mode.
Disconnected
Connecting...
Starting fast init connection.
Connecting to address 0x01.
Fast init sent, sending start communication request.
Switching to KWP2000 session.
Connected
Disabling Windows sleep mode.
Reading ECU flash memory.
ECU reports programming session preconditions have been met.
Negotiating communication timings.
Successfully changed to new communication timings.
Requesting security access.
ECU reports that security access is not supported.
Starting diagnostic session.
Failed to start diagnostic session.
Received negative message response with code: GeneralReject
Reading ECU flash memory failed.
100% complete.
Restoring Windows sleep mode.


Reading all ECU info.
Starting diagnostic session.
Successfully started diagnostic session.
Negotiating communication timings.
Successfully changed to new communication timings.
0% complete.
25% complete.
50% complete.
75% complete.
100% complete.
Read 4 ECU info entries:
« Last Edit: May 25, 2014, 02:18:37 PM by LHN86 » Logged

BMW E30 M3 S54
TLS
Full Member
***

Karma: +1/-0
Offline Offline

Posts: 62


« Reply #1 on: July 28, 2014, 06:06:08 PM »

I see similar with my 4B0906018.
Slow init works fine. I can't connect with memory layout 400 series. I can connect with memory layout 800 series, but it doesn't read properly after 63%. I should apparently get a 512k file but I get a 1024k one. All the 4B0 ones I have seen are 512k except for Rob MWPropane's TT which is a 1024.
Some have had success as per here  http://nefariousmotorsports.com/forum/index.php?topic=366.0 but I don't make sense of it.

Sorry if that is not much help.

Logged
TCSTigersClaw
Sr. Member
****

Karma: +15/-6
Offline Offline

Posts: 353



« Reply #2 on: July 29, 2014, 12:42:58 AM »

it doesnt matter , even if you read a 1024 file convert it to 512.

To make it easy import it o an already 512 ori file and Winols will chop it for you
Logged

VAG cars newbie tuner Smiley
LHN86
Full Member
***

Karma: +5/-1
Offline Offline

Posts: 63


Engineer


« Reply #3 on: August 05, 2014, 03:27:18 AM »

Thanks for posting guys! My problem is that I can not read nothong that all:(
Logged

BMW E30 M3 S54
LHN86
Full Member
***

Karma: +5/-1
Offline Offline

Posts: 63


Engineer


« Reply #4 on: October 31, 2014, 04:22:15 AM »

Someone seen this bug before? Is it possible that the flash installed in the ecu is not compatible by reading from obd?
Logged

BMW E30 M3 S54
ddillenger
Hero Member
*****

Karma: +637/-21
Offline Offline

Posts: 5640


« Reply #5 on: October 31, 2014, 09:17:29 AM »

Someone seen this bug before? Is it possible that the flash installed in the ecu is not compatible by reading from obd?

Lower your baud to 38400 AFTER connecting, try again. Security access is irrelevant.
Logged

Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM
LHN86
Full Member
***

Karma: +5/-1
Offline Offline

Posts: 63


Engineer


« Reply #6 on: November 02, 2014, 12:51:41 PM »

Thanks for help ddillenger! It still gives me the general reject in attempt to make a flash read.
Logged

BMW E30 M3 S54
em.Euro.R18
Full Member
***

Karma: +4/-5
Offline Offline

Posts: 219


« Reply #7 on: January 29, 2015, 02:40:41 PM »

52800 layout 800BB always worked for me. You may need to go lower if its still not reading.
Logged
TijnCU
Hero Member
*****

Karma: +60/-4
Offline Offline

Posts: 690


flying brick


« Reply #8 on: February 01, 2015, 03:45:20 AM »

I have had lots of troubles reading on these ecu's, my ori only read out via bootmode galetto. Writing works fine though (slow init). Sometimes it fails and disconnects, but if you dont touch the ignition and just reconnect it will start flashing right after it has reconnected.
« Last Edit: February 01, 2015, 03:50:07 AM by TijnCU » Logged

TCSTigersClaw
Sr. Member
****

Karma: +15/-6
Offline Offline

Posts: 353



« Reply #9 on: February 03, 2015, 12:26:47 AM »

Some ECu`s cant be read with nefmoto no matter what Sad  , even with other tools you have to force read or something similar to read it.

I have problems only with Audi ECu`s
Logged

VAG cars newbie tuner Smiley
LHN86
Full Member
***

Karma: +5/-1
Offline Offline

Posts: 63


Engineer


« Reply #10 on: February 03, 2015, 12:51:52 AM »

I think TCSTigersClaw has right. I gave up and soldered in a socket. This was the esiest way for this ecu I beleive. The "flash" its self was produced in 93 and has memory layout 400BS or something, never seen before :/
Logged

BMW E30 M3 S54
Ne-FF
Jr. Member
**

Karma: +0/-0
Offline Offline

Posts: 25


« Reply #11 on: April 21, 2015, 11:21:28 PM »

I have had lots of troubles reading on these ecu's, my ori only read out via bootmode galetto. Writing works fine though (slow init). Sometimes it fails and disconnects, but if you dont touch the ignition and just reconnect it will start flashing right after it has reconnected.

Does it mean that i can read my 018P flash using 800BB, get 1024 file, convert it to 524 in WINOls?
and what memory layout should i use for writing? 400BB with slow init?
Logged

A4 B5 1.8TQM // 312mm/280mm brakes // 240 mm clutch
ddillenger
Hero Member
*****

Karma: +637/-21
Offline Offline

Posts: 5640


« Reply #12 on: April 22, 2015, 12:06:23 AM »

I just did one of these today, both read and write. Just use 38400 baud, and ignore the validation failure. Everything will be fine.
Logged

Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM
Ne-FF
Jr. Member
**

Karma: +0/-0
Offline Offline

Posts: 25


« Reply #13 on: April 22, 2015, 12:44:33 AM »

I just did one of these today, both read and write. Just use 38400 baud, and ignore the validation failure. Everything will be fine.

Did you read and write it using 400BB?
Logged

A4 B5 1.8TQM // 312mm/280mm brakes // 240 mm clutch
Ne-FF
Jr. Member
**

Karma: +0/-0
Offline Offline

Posts: 25


« Reply #14 on: April 22, 2015, 01:22:57 AM »

i solved the problem ) i had to instal last version fo nefmoto soft ))
now I can read it
« Last Edit: April 22, 2015, 08:23:25 AM by NemudroFF » Logged

A4 B5 1.8TQM // 312mm/280mm brakes // 240 mm clutch
Pages: [1] 2
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.044 seconds with 17 queries. (Pretty URLs adds 0.001s, 0q)