chlippo
Newbie
Karma: +0/-0
 Offline
Posts: 22
|
 |
« on: June 10, 2014, 06:23:21 PM »
|
|
|
Its been a while and I am still not able to connect Me7logger I seriously need help.
What i did is take out the instrument cluster and behind there is a green connector on the right side. I opened this connector and take a piece of wire to connect 2 wires together, the wire that goes to pin 5 with the wire from pin 28, leave the pins like they were in the connector. I actually wired those to an outside switch so I can connect and disconnect those pins anytime without taking the cluster out.
I still loose connection when i turn ignition on.
Then I tried to remove the instrument cluster fuse. I dont recall which fuse was it but when I took it off the instrument cluster turned off, no lights. I started the car, removed the fuse, and tried to connect the logger, still loose connection
The logger works fine while the car is off and key is in ignition, when I turn the ignition on (even without turning the car on) the logger looses connection.
What to do??
Is it a cable problem?
|
|
|
|
|
Logged
|
|
|
|
chlippo
Newbie
Karma: +0/-0
Offline
Posts: 22
|
|
« Reply #1 on: June 13, 2014, 03:38:53 AM »
|
|
|
I tried to remove radio fuse, logger didn't work neither.
As soon as I turn the key the logging stops.
What am I doing wrong?
Is it connected to the baud rate and similar details?
|
|
|
|
|
Logged
|
|
|
|
|
adam-
|
|
« Reply #2 on: August 20, 2014, 07:35:58 AM »
|
|
|
Mine was doing this, MK4 AUM with the stupid Bosch clocks.
Would connect with key in, but as soon as you turned the ignition on, it would drop out. Started the car, removed the cluster fuse (so that the immo had auth. properly), and it would connect.
Happy days! I think if it's not connecting even without the cluster fuse, you're gonna have to run another OBD port separate to the orig. (With all the other k-lines disconnected).
|
|
|
|
|
Logged
|
|
|
|
kingkhalilz
Full Member
Karma: +0/-0
Offline
Posts: 123
|
|
« Reply #3 on: August 30, 2014, 01:44:17 PM »
|
|
|
Chlippo, You are not alone i have the exact same problem. I think the next thing to do it rewire the k-line directly from the ecu to the obd 2 port. That way it bypasses the instrument cluster. I think this will cause problems however with values for the cluster. Im stuck just like you.
|
|
|
|
|
Logged
|
|
|
|
kingkhalilz
Full Member
Karma: +0/-0
Offline
Posts: 123
|
|
« Reply #4 on: August 31, 2014, 01:49:35 PM »
|
|
|
Pulling the fuses and changing to 0x00slow didnt do anything for me. Still trying things
|
|
|
|
|
Logged
|
|
|
|
TLS
Full Member
Karma: +1/-0
Offline
Posts: 62
|
|
« Reply #5 on: September 01, 2014, 08:36:53 PM »
|
|
|
I'm in the same boat. It logs fine with Nefmoto, but not with Setzi.
Also, I pull every fuse and my cluster stays on.
|
|
|
|
|
Logged
|
|
|
|
kingkhalilz
Full Member
Karma: +0/-0
Offline
Posts: 123
|
|
« Reply #6 on: September 02, 2014, 03:45:00 PM »
|
|
|
I will try and log using nefmoto.
|
|
|
|
|
Logged
|
|
|
|
kingkhalilz
Full Member
Karma: +0/-0
Offline
Posts: 123
|
|
« Reply #7 on: September 04, 2014, 11:53:41 AM »
|
|
|
Funny i pulled the .bin file from my ecu using nefmoto. But then i started the car to try and log using nefmoto and boom
01.
Slow init succeeded.
Switching to KWP2000 session.
Connected
Disconnecting because no response was received for the Tester Present message.
Disconnected
|
|
|
|
|
Logged
|
|
|
|
|
ddillenger
|
|
« Reply #8 on: September 04, 2014, 12:20:35 PM »
|
|
|
Funny i pulled the .bin file from my ecu using nefmoto. But then i started the car to try and log using nefmoto and boom
01.
Slow init succeeded.
Switching to KWP2000 session.
Connected
Disconnecting because no response was received for the Tester Present message.
Disconnected
Is your ABS module bad? |
|
|
|
|
Logged
|
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
|
|
|
kingkhalilz
Full Member
Karma: +0/-0
Offline
Posts: 123
|
|
« Reply #9 on: September 04, 2014, 01:27:35 PM »
|
|
|
Not sure if the module is actually bad it has code for speed sensor. Should i unplug that bastard??
|
|
|
|
|
Logged
|
|
|
|
|
ddillenger
|
|
« Reply #10 on: September 04, 2014, 01:41:29 PM »
|
|
|
Not sure if the module is actually bad it has code for speed sensor. Should i unplug that bastard??
Yes. |
|
|
|
|
Logged
|
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
|
|
|
kingkhalilz
Full Member
Karma: +0/-0
Offline
Posts: 123
|
|
« Reply #11 on: September 04, 2014, 01:43:52 PM »
|
|
|
Will try!!
|
|
|
|
|
Logged
|
|
|
|
kingkhalilz
Full Member
Karma: +0/-0
Offline
Posts: 123
|
|
« Reply #12 on: September 04, 2014, 04:17:40 PM »
|
|
|
No luck with it. same thing. My radio is in safe mode would that change anything??
|
|
|
|
|
Logged
|
|
|
|
|
ddillenger
|
|
« Reply #13 on: September 04, 2014, 05:12:46 PM »
|
|
|
Unlikely. Download and install join.me and I will login and see if I can figure it out.
|
|
|
|
|
Logged
|
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
|
|
|
kingkhalilz
Full Member
Karma: +0/-0
Offline
Posts: 123
|
|
« Reply #14 on: September 04, 2014, 09:46:21 PM »
|
|
|
I downloaded it, let me know.
|
|
|
|
« Last Edit: September 04, 2014, 09:54:24 PM by kingkhalilz »
|
Logged
|
|
|
|
|
