Pages: [1]
Author Topic: Cable will not connect with nefmoto  (Read 11630 times)
thelastleroy
Sr. Member
****

Karma: +19/-2
Offline Offline

Posts: 260



« on: July 25, 2014, 05:59:52 PM »

Hello, and sorry to ask another connection thread, but I've been searching and trying to no avail. I am attempting to connect in vehicle.

I have tried just about every driver I can find for the black ross-tech copy cable from ebay:

http://cgi.ebay.ca/ws/eBayISAPI.dll?ViewItem&item=201134111763

I am currently able to connect to the ecu with vag-com via this cable, check fault codes etc. I wasn't able to get any kind of action at all at first with nefmoto, until I found via search on the forum that some people had to UNcheck the "should verify cable in dumb mode" box in the settings. After I did that I get this result for every possible baud speed and configuration, fast and slow:


Disconnected
Connecting...
Starting slow init connection.
Connecting to address 0x01.
Slow init failed.
Disconnected
Connecting...
Starting slow init connection.
Connecting to address 0x01.
Slow init failed.
Disconnected
Connecting...
Starting slow init connection.
Connecting to address 0x01.
Slow init failed.
Disconnected

Disconnected
Connecting...
Starting fast init connection.
Connecting to address 0x01.
Fast init sent, sending start communication request.
Start communication request did not receive any response.
Disconnected
Connecting...
Starting fast init connection.
Connecting to address 0x01.
Fast init sent, sending start communication request.
Start communication request did not receive any response.
Disconnected
Connecting...
Starting fast init connection.
Connecting to address 0x01.
Fast init sent, sending start communication request.
Start communication request did not receive any response.
Disconnected

Disconnected
Connecting...
Starting slow init connection.
Connecting to address 0x01.
Slow init failed.
Disconnected
Connecting...
Starting slow init connection.
Connecting to address 0x01.
Slow init failed.
Disconnected
Connecting...
Starting slow init connection.
Connecting to address 0x01.
Slow init failed.
Disconnected

Any ideas? would really like to start tinkering and learning how to use the software, but I simply can't connect!!

Im running XP home edition on the laptop

EDIT:

Tried pulling cluster fuse, did not change connectivity.



« Last Edit: July 25, 2014, 08:15:01 PM by thelastleroy » Logged
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12232


WWW
« Reply #1 on: July 25, 2014, 08:19:07 PM »

Get an ftdi cable, not a rosstech clone..

or buy a real ross tech cable..
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
thelastleroy
Sr. Member
****

Karma: +19/-2
Offline Offline

Posts: 260



« Reply #2 on: July 25, 2014, 08:28:24 PM »

Get an ftdi cable, not a rosstech clone..

or buy a real ross tech cable..


Unfortunately, I thought I was buying an FTDI cable, check the ebay link at the top of the OP. The description says FTDI, which is what I need based on what I read here in the faq/getting started. As soon as I plugged it in and loaded the drivers, the laptop says its ross-tech. Or at least thinks it's ross-tech.

So I need a new cable. The cheap blue ones work apparently?
Logged
ddillenger
Hero Member
*****

Karma: +637/-21
Offline Offline

Posts: 5640


« Reply #3 on: July 25, 2014, 08:47:41 PM »

There is a sticky.

"Cables that you, the members.....(something about confirmed working)"

Check it out, and then post the one you end up buying, and if it works. Smiley
Logged

Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM
thelastleroy
Sr. Member
****

Karma: +19/-2
Offline Offline

Posts: 260



« Reply #4 on: July 26, 2014, 06:04:25 AM »

There is a sticky.

"Cables that you, the members.....(something about confirmed working)"

Check it out, and then post the one you end up buying, and if it works. Smiley

ddillenger, thanks for the reply. I guess not every cable on fleabay that looks the part will play nice....

I just ordered this cable on your recommendation from the "known good cables" thread:

http://www.ebay.com/itm/281312477303?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT

*edit*

A few weeks later, and this cable works for read/write with NefMoto. Stoked!

we'll see how it goes in a couple of weeks. I will post in the cables thread once confirmed working.

« Last Edit: August 18, 2014, 07:13:19 PM by thelastleroy » Logged
RistoEe
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 1


« Reply #5 on: September 01, 2014, 05:49:55 AM »

I think this one is a proper topic. I have genuine Ross-Tech cable (HEX-COM) and since it's a RS232  and my laptop doesn't have RS232-port so I have RS232-USB adapter (UC-232A) and for this the right drivers is ATEN USB to serial. So the shorten version: RossTech -> serial to USB -> laptop (Lenovo T400s, Win7 32-bit).

I've tried to uninstall those ATEN drivers and then install FTID or RossTech's VCP drivers with no success. And if I try to install over the ATEN drivers, windos just tells that the ATEN drivers are best and doesn't install other drivers. Is there anyway to get this kind of combination to work with Nefmoto? Or do I have to just buy one more cable for Nefmoto? And I have unchecked from VCDS that "Boot in intelligent mode" etc.

Oh, and the main problem is, that NefMoto doesn't recognize the cable.

e: Tried my genuine Galletto cable and Nefmoto recognize that one. But the problem with Galletto cable is that it doesn't connect with the car in Nefmoto. Any ideas? I enabled the VCP in FGTech USB driver, but can't get any drivers installed for it.
« Last Edit: September 01, 2014, 09:09:18 AM by RistoEe » Logged
terminator
Sr. Member
****

Karma: +15/-4
Offline Offline

Posts: 425


« Reply #6 on: September 04, 2014, 03:05:48 PM »

Get an ftdi cable, not a rosstech clone..

or buy a real ross tech cable..

Nefmoto works with original Ross tech?  Shocked
Logged
turboat
Hero Member
*****

Karma: +44/-3
Offline Offline

Posts: 619


« Reply #7 on: September 05, 2014, 12:56:25 AM »

Yep, in dumb mode.
Logged
terminator
Sr. Member
****

Karma: +15/-4
Offline Offline

Posts: 425


« Reply #8 on: September 05, 2014, 06:35:38 AM »

Thanks, will try it.
Logged
turboat
Hero Member
*****

Karma: +44/-3
Offline Offline

Posts: 619


« Reply #9 on: September 05, 2014, 06:52:12 AM »

See top post/pic here: http://nefariousmotorsports.com/forum/index.php?topic=6537.0title=
Logged
terminator
Sr. Member
****

Karma: +15/-4
Offline Offline

Posts: 425


« Reply #10 on: September 05, 2014, 02:19:41 PM »

Thanks, really good work!
Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.029 seconds with 18 queries. (Pretty URLs adds 0.001s, 0q)